Jump to content
SAU Community

Recommended Posts

putting some bits and bobs up i have about the place not being used

will get pics up when i get a chance or text me and ill mms them thru

located northern nsw bout 30mins over the boarder

can usually meet up the coast but if needed

text preferred on 0435494669

R33 rear brake setup complete with hand blake lines etc -$300

R33 cat back 3inch straight thru into twin 3 inch pipes (not the prettiest but does the job) -$200

post-48080-0-99275100-1348481423_thumb.jpg

post-48080-0-56424500-1348481435_thumb.jpg

pretty much any R33 panels just hit me up what you need

RB20 stock turbo -$100

RB exhaust manifold with a t2 adaptor plate welded to it,with 3 inch stainless dump and front pipes to suit a sr dump flange so sr suited turbos are direct bolt on -$200

RB20 cross member -$100

RB oil cooler setup (just uses rubber hose not braided) -$150

post-48080-0-07249400-1348481410_thumb.jpg

600x300x75mm front mount used condition -$100

R33 gtr intercooler used condition -$200

R32 bonnet couple little dimples -$100

R32 lsd -$200

R32/S13 hicas lock bar -$80

R34 front gaurds

good condition in silver -$100 each

CA18 brand new stainless low mount tuned length manifold -$200

post-48080-0-65460100-1348481364_thumb.jpg

post-48080-0-07991800-1348481381_thumb.jpg

SR20 stainless bellmouth dump and frontpipe -$200

(best SR dump ive ever seen icon_e_wink.gif)

post-48080-0-67200300-1348481449_thumb.jpg

post-48080-0-56556400-1348481466_thumb.jpg

S14 APEXI 3inch cat back with muffler and canon (very good condition apart from couple scraps on the muffler)-$300

GT35R-just a china .70 front 1.06 rear, water and oil cooled only been on car 100ks

still on car atm if anyone wants to see it run ive just decided to go a smaller turbo -$300

post-48080-0-55175500-1348481348_thumb.jpg

gizzmo electronic boost controller -$200

post-48080-0-61017300-1348481327_thumb.jpg

autometer 5inch tacho with shift light silver face -$100

post-48080-0-98291700-1348481304_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/410069-bit-of-this-bit-of-that/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...