Jump to content
SAU Community

Recommended Posts

Hey guys Located in Sydney, contact 04 21 451 965 (prefer pick up, may post at buyers expense)

Have a brand new in the box and still sealed in plastic bosch 044 with a brand new surge, not some dodgy ebay overseas job, was made correctly want both items gone $ 250 for both

Also have a Brand new in the box never used turbosmart pro-gate 50 mm ext gate blue, 600 ono (goes for something ridiculous like 900 on the site

also have 80 mm throttle body, suit rb25, brand new 120

Also have an rb25/30 with an r33 gtst box

the block has 20 thou over, JE pistons, h-beam rods, new ACL rings, bearing, gasket, 2000 cc boschy indy blue injectrs, greddy style plenum, stage 1 poncams, new oil pump, r33 gear box with brass button twin plate clutch, bought of someone else whose funding had run out to complete, lost my interest in this side project and want this and everything with it gone, its had a full rebuilt hasnt been run since the rebuild, after 3500 ono for the engine realistically I will take 3200, dont offer me lower then that, and 1400 ono for the box and clutch included, not keen on seperating the box from the engine untill the engine is sold, if your after both together (its still connected) or you can take it all for 4300, anyway enough rambling on

Pics

post-103063-0-21227800-1355453341_thumb.jpgpost-103063-0-87867200-1355453354_thumb.jpgpost-103063-0-55280500-1355453369_thumb.jpgpost-103063-0-62720500-1355453380_thumb.jpgpost-103063-0-16178200-1355453391_thumb.jpgpost-103063-0-66878700-1355453402_thumb.jpgpost-103063-0-65573500-1355453413_thumb.jpg post-103063-0-44422900-1355453565_thumb.jpgpost-103063-0-52428300-1355453579_thumb.jpgpost-103063-0-39958500-1355453590_thumb.jpg

Edited by GTR_77

Had a couple questions on the pump it is genuine and does have czech republic stamped on the side, not germany and it is stamped properly not dodgy

http://trolltuner.com/?p=692

If your after the pump alone im after 200

Sorry mate not parting out the motor, have been receiving alot of interest and calls about the motor, price of the motor will also be going up once I have validated the internals come this monday. If the current interested party's dont end up wanting it, pics and proof will be posted along with the new price so please disregard the current one.

Bosch 044 and surge tank SOLD

Brand new Turbosmart pro gate price drop to $500

Edited by GTR_77

Engine is now SOLD pending payment.

Also have a picture of the gearbox and clutch

its a Xtreme twin plate ceramic clutch which is new and never used its 1300 for it in the box brand new im after 950 ono

manual rb25 turbo gearbox 1400 ono

post-103063-0-61999800-1356657340_thumb.jpg

post-103063-0-42218500-1356657349_thumb.jpg

post-103063-0-82154200-1356657357_thumb.jpg

post-103063-0-36895600-1356657364_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...