Jump to content
SAU Community

Recommended Posts

i have several things up for sale all items are located in perth WA and can be shipped for $15 registered post (except sub)

can pm or call 0466672245

gfb fully adjustable hybrid bov

can be adjusted to run full atmospheric to full plumb back and inbetween.

fitted to my car used for a few days but wasnt really my thing.can be used on any turbo charged engine when installed correctly as it is made for a universal fit but currently set up for R33,R34 skyline and M35 stagea with a turbosmart adaptor

selling for $150 as a family member threw out box with manual and allan keys so comes as is

here is the instructions for fitment

http://www.gfb.com.au/installation-instructions/21

gfb atmoic manual boost controller bleed valve type.

as new in box,fitted to my car used for a few days but im looking at getting a electric boost controller so i want this gone.can be used on any turbo charged engine when installed correctly

sell for $50

http://www.gfb.com.au/products/boost-controllers/atomic

Hertz 15" Dual Coil subwoofer

by having dual coil it provides the kick of a 12" sub with the bass drop of a 15".its peak power is 1400watt rms and it requires 700watt rms continuious power.reason for sale is i wont be putting this in my new car.the sub originally cost me $1200 and i had a custom made sealed box which was a additonal $400.i ran this with a stinger capacitor and a 1000watt rms alpine pdx with great results.

sell for $450 need it gone

Stinger fused distribution box (postive) and un-fused (negatime)

i used the fused for postive and the unfused for negative was in car for 11 months on high powered stereo and worked great

note orange cable in picture is my stereo wire and is now removed

sell both for $50

Stinger SHT301 postive with volts meter and SHT303 negative

were on the car for two weeks as i needed different terminals.i lost one of the allan key headed screws on the negative,one replaced with a hex bolt cut to length;its fine.can be used for 1/0 ga leads

sell both for $50

post-103368-0-65698500-1357446658_thumb.jpg

post-103368-0-80974100-1357446662_thumb.jpg

post-103368-0-25201100-1357446665_thumb.jpg

post-103368-0-57512100-1357446668_thumb.jpg

post-103368-0-67502800-1357446671_thumb.jpg

post-103368-0-56870600-1357446746_thumb.jpg

post-103368-0-28489600-1357446748_thumb.jpg

post-103368-0-79480500-1357446750_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...