Jump to content
SAU Community

Recommended Posts

Hi guys

Time to clean out all the extra parts i have laying around the garage

All items located at Prestons Sydney, im not shipping this stuff so its pick up only

As stated in title this stuff is already cheap so some stuff im not neg on

First up

3.5" to 3" inch Catalytic converter, Has the usualy scratches on the underside but internally its %100 $50

post-47556-0-31586900-1358308952_thumb.jpg

post-47556-0-53259100-1358308981_thumb.jpg

next is a Greddy Y pipe (excellent for those guys doing a single mount single) good condition and comes with 2 silicon adapters with step downs for filters. Bought this for $200, selling it for $140

post-47556-0-71618400-1358309078_thumb.jpg

Standard R32 GTR wing .. one of its mounting bolts spins in its housing but be fixed with not too much difficulty.. apart from that just needs a wipe down and is in good condition with a few small scratches $50

post-47556-0-70227000-1358309576_thumb.jpg

Next is some standard parts

6x coil packs and ignitor.. started to misfire at 350rwkw so these would be good as a replacement for anything around 300rwkw and under

Ignitor $30

Coil packs $60

Blue Radiator hoses with 4 beefy clamps to suit GTR.. in good condition, just a bit dirty and need a wipe down $25

post-47556-0-66442400-1358309848_thumb.jpg

Some random BOV and turbo pluming from my old twin set up.. all in good condition. also have the BOV cross over pipe as is seen in the picture with the GTR wing.. Enquire for pricing, will still sell for cheap :D

post-47556-0-80795900-1358309918_thumb.jpg

Standard GTR Charcoal Canister for you emission nuts ;) $30

Standard R32 GTR intercooler... has a few bent fins and dings but works perfectly fine.. painted black..want it gone!! $30

Standard R32 GTR Manifolds.. good condition, would be ideal for someone wanting to do some porting $25

Standard GTR rods and pistons.. all rods are in good conditon, one of the pistons is fooked!! whole lot for $30

if theres more ill update

PM or message me 0432528844

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...