Jump to content
SAU Community

Recommended Posts

So looked around about this and it's very hard to find someone with exactly the same problem so here it goes for my problem and hopefully will give reference to others in the future.

Will try get a video ASAP

So car is fine and dandy as I'm driving along, on hot days but don't know if it's the weather that has anything to do with it as I work nights at the moment and have no chance of driving her when it's cool. All of a sudden I driving along and te car will drop maybe 200 rpm and it will feel rumbly as it idles. Now when I accelerate it feels as if te car is choking on something , I hit 4000 revs and it starts to go away but tends to missfire a bit , at this point. Get home turn her off, drive later it's fine untill later on while driving again . Note sometimes it had gone away while driving. So I've changed spark plus and cleaned the throttle body as I thought maybe its got gunk in there, spark plugs were a bit flooded so those were changed to new ones which the girl at repco stuffed up and have me platinums instead of copper.

So what's my next step to check, I checked the coilpacks and they seemed to be clean.

Your time and effort in assisting me will be greaty appreciated

And the car of course

1996 r33 gtr series 2

Stock engine

Straight through exhaust

Link to comment
https://www.sau.com.au/forums/topic/419190-my-r33-likes-to-chuga-chug-chug/
Share on other sites

Try re-soldering the AFM, there is a 'how to' on here somewhere. Or get another known good unit to try. Most times an intermittent fault like this one is due to dry solder joints inside the AFM.

best to trouble shoot and solve yourself before getting to the tune/dyno as if it isnt they will be charging you top dollar to trouble shoot your car, as well as to fix the problem that you could have easily done so from home...

Okay well then I'm changing mechanics, as mine said the tune should fix if but failed to tell me what it was as he didn't know what it was. Ill give another place a go, try run the car and bring it to them with the problem, if they can't tell by a quick drive ill ask to book a dyno run and have it faulting before I jump on

Try re-soldering the AFM, there is a 'how to' on here somewhere. Or get another known good unit to try. Most times an intermittent fault like this one is due to dry solder joints inside the AFM.

+1

Don't waste your time doing anything else before doing this. Speaking from experience.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...