Jump to content
SAU Community

Recommended Posts

selling a couple of sets of wheels and some other bits

located on the sunshine coast for pick up

text me whenever ** 0434282866 **

open to swaps for 32/gtr/cefiro/86 parts, if you would like to negotiate a price just hit me up.

selling my 18" Sparco NT wheels off my R32, fronts are 8.5 rears are 9.5 both 38 offset i think. these wheels are getting real hard to find (especially in black) and they are quite OG. LHS has a bit of gutter rash nothing serious, RHS almost none, paint in very good conditon

235/40/18 dunlop sp sport 300 tyres all round 50% on three of them, one of the rears has the outer edges worn.

wheels were almost 6k new. 5x114.3

asking $1600

will come with the special little wheel nuts and tool. as well as all four mint sparco center caps (which are quite cool) and a little slip on spacer i was using on the front

5a2lnr.jpg

dlq25h.jpg

2m6o485.jpg

2ni1yqo.jpg

Selling the bosses rotas rbx i think they/re called

17x9 -13 (x2) and 17x9.5 -19 (x2)

very good condition on drivin on a few times, very light gutter rash on one

4x114.3. 80% tread on tyres (goodyear 215/45/17)

asking $1100 (missing one center cap)

30ti17a.jpg

2rr9xnd.jpg

selling an rb20 mostly complete, has manifold no turbo/lines

ran fine before it pulled out. basically a long motor with injectors/line

rocker covers just painted in wrinkle red

$250, will split covers (they do have breather fittings) make an offer

2s6lf1t.jpg

35miqg5.jpg

selling TRUST intercooler with piping to suit standard set up. $50

167ry2r.jpg

also i have an r31 runs well drives good. no interior and body is a bit beaten up, head lights and bumper ok (series 3) would like to get rid of entire care $700, but make me an offer.(its manual)

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...