Jump to content
SAU Community

Nsw - Drift Carbon Bucket Seats, Bov, S14/ Sr20 Injectors, Manual Conversion Parts.

Mski
 Share

Recommended Posts

Mski Newbie

Mski

Posted
Posted
Selling various S14 / SR20 parts. Trying to make room / support finances as First child is on the way!

negotiable on price somewhat


Open to trade for:

s14 boot lid no holes

Suspension arms for s14

Possibly Wheels- Something in 17 or 18 inch 8 + inch wide with low offset.


Seats - Drift brand carbon seats on modified bride rail for S13/14/15 ( sit a little lower than standard seats in my s14). Have been retrimmed by house of Trim in black leather ( by previous owner). Pictures below are the exact same seats, but the ones on offer have red stitching, not yellow. Great seats that are ADR approved and very comfy. $1200 ONO or less without Rails.


Turbosmart Dual port BOV with blanking plug and trumpet. Was on car when I bought it. Works fine - $100


740cc high flowed JECS injectors for SR20. PJ's Quick bits high flowed these. Were put in for one dyno tune day then removed - $150


Stock s14 VCT OEM camshafts - $30


S14 manual clutch pedal and manual cross member - $20 each


S14 auto gearbox, flywheel, torque converter and cross member - Running fine before reomval, 150,000 KM - $free


Nismo big clutch slave cylinder for sr20 - cost $185 new, used for 3 days, removed - $100



Located near blacktown, Western Sydney, will post smaller items


SMS on zero four zero five 557011 for more info



Pictures:


62069475952ff8283e83o.jpg

photorbq.jpg

photo2juo.jpg

photo4gjx.jpg

photo3tso.jpg

photo5fo.jpg

photo6px.jpg

photo7tw.jpg

photo8an.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      No, so what happened is. I put a bunch of filler then I sanded it all down, I removed all the filler (unintentionally), then I put the epoxy primer on because that section of the panel is bare metal. The car is parked outside so I needed to protect it in the meantime incase it rains.
    • r32-25t
      Shoota's R33 GT-R RB30/26

      By r32-25t · Posted

      It’s definitely an import, the Aussie ones have reflectors in the rear bar, it’s also a turbo which none of the Aussie one were.    I remember back in the day I want a twin turbo z32 so bad and then I saw a 32 gtr and that was the end of that lol 
    • MBS206
      Shoota's R33 GT-R RB30/26

      By MBS206 · Posted

      Same can be said for Subarus motors ha ha!   I like the 300ZX, I nearly bought a Z32 before I bought my first Skyline. It was going to be a project. Then I found out there was a bit of a dodgy title with it... As in, someone attempted to commit insurance fraud with it and there was now some dodgy legalities around it. So at 18 I walked away from it.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      The below is what the readings I had with the fuel pressure gauge which were correct. It seems like the issue is mainly during drive and not idle. I bought the new hanger hoping it could be the issue, perhaps I ruined something while cleaning, but I have not installed it yet since I have to wire up everything with the new plugs.
    • GoHashiriya
      R34 Skyline Sunroof Won't Tilt/Vent

      By GoHashiriya · Posted

      Actually, that's not entirely true. It's also the same motor in the 1st gen Nissan Cube but they're rare as hen's teeth.  
×
×
  • Create New...