Jump to content
SAU Community

New * Walbro * 255Lph In-Tank Fuel Pump Gss342 + Fittings - $115 Incl. Delivery

VultureMotorsport
 Share

Recommended Posts

VultureMotorsport Mentor

VultureMotorsport

Posted
Posted

Genuine WALBRO 255LPH Fuel Pump GSS342 + Fittings


- Most commonly used 38mm in-tank performance fuel pump
- 255LPH @ 3 BAR
- Genuine WALBRO – manufactured in USA with original packaging
- Very popular in-tank pump upgrade for Skyline's (practically straight drop-in)
- Includes 2x strainers and fittings as pictured

$115 incl. Delivery >> SAU Special

BUY_BUTTON.gif

* This is an Australian delivered product with a national warranty.

Offset GSS341 also available @ same price on request.

GSS342_350.jpgGSS341_350.jpg

COMES WITH THE LOT FOR A QUICK INSTALL

slusarczykr33 Contributor

slusarczykr33

Posted
Posted (edited)

sorry new at this, how much power is this one good for and whats the difference between internal and external apart from the obvious.

Edited by slusarczykr33
VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

sorry new at this, how much power is this one good for and whats the difference between internal and external apart from the obvious.

Hey,

It's rated for around 300-400HP, so more then enough for most applications.

In most cases vehicles are fitted with one internal fuel pump which inside of the assembly, so if you are looking for a quick fuel pump upgrade that will be your best bet.

You can purchase an external fuel pump which are usually larger unit's but required modifications.

What are you planning to fit this too?

Hope that helps,

Brendan

(VM)

VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

r33 gtr and plan on having 450-500 mark do you have one suitable for that range?

Hey,

Go with the E85 Walbro unit - flows 460LPH which is the highest rate of any 38mm in-tank pump on the market today.

You can purcahse it here: http://www.skylinesaustralia.com/forums/topic/410989-all-new-walbro-460lph-e85-in-tank-fuel-pump-strainer-kit/

Cheers,

Brendan

(VM)

  • 4 weeks later...
VultureMotorsport Mentor

VultureMotorsport

Posted
  • Author
Posted

Does this fit the s15?

Hey!

These are very common on all S14/S15's and fit real easy being a 38mm unit. Some adjustment may be required as these are universal.

Cheers,

Brendan

  • 2 weeks later...
  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...