Jump to content
SAU Community

Nitrogen Leaking From Tyres?

2FA54U

By 2FA54U,
in R35 GTR

 Share

Recommended Posts

2FA54U Enthusiast

2FA54U

Posted
Posted

Has anyone had a problem with nitrogen leaking or anything I had mine done a month ago and I had a warning light come up so I've had them filled again and it hasn't even been a week and my lights come on again. What do you's think it would be? I hope it's not the tyres they are pretty much new not even 5000kms on them

Link to comment
https://www.sau.com.au/forums/topic/424693-nitrogen-leaking-from-tyres/
Share on other sites
GTRsean Grand Master

GTRsean

Posted
Posted

If it's one tyre, a nail or something.

If all tyres are doing it....average temp drop due to winter?, as even nitrogen expands and contracts too due to temperature, just not as much as the usual plain 'air'.

Slayermatic Rookie

Slayermatic

Posted
Posted

It will be a slow leak. I had the same problem with one of my tyres. If you have runflats it will usually mean a whole new tyre depending on the where the damage is and if the tyre place will be willing to repair it.

MJR35 Enthusiast

MJR35

Posted
Posted

Jason, that sounds strange.. What pressures are you running them Cold ? I run mine around 32PSI cold, and i have noticed all the tyres have lost approximately 1psi over the past 7 weeks. (Could be colder climate).. But to lose pressures to the point of Low Pressure on the Dash indicator after a week doesnt sound right, Have you manually checked the tyre pressures to see if the Pressure Monitoring system was right there is a low pressure problem ? If tyre pressures checked via Gauge is OK, you may need the TPMS sensors reset, which i believe is a something you need the Dealer to do ..

2FA54U Enthusiast

2FA54U

Posted
  • Author
Posted

I'm going to get it checked tomorrow and when I got my first warning light on I checked had all the tyres checked and most were around 29 and 28 then one of them we 26 and they were pumped to 32psi... I recently had them set to 31 just last week so it will be interesting to see if its the same tyre which was low last time... Also lets say it was a tyre that's damaged am I better off replacing the 2 or just the one?

MJR35 Enthusiast

MJR35

Posted
Posted

Jason, unless the tyres are very new, you should always replace Tyres in pairs (Ie: Front Pair or Rear Pair ).. If you dont , you may end up with different grip profiles with a new and worn tyre from left to right, and you also have differing rolling circumferences which may put further strain on the Diffs.

But you should get the Dealer to really check whats going on with the Tyre thats going down before making any changes.. (It could be as simple as a faulty valve)

2FA54U Enthusiast

2FA54U

Posted
  • Author
Posted

Yeah I thought so it says in the manual to replace all 4 if any are damaged for even wear I just bought 2 rears and it cost me $1260 delivered to my door not bad but pretty dear for the damage of one screw :(

2FA54U Enthusiast

2FA54U

Posted
  • Author
Posted

Nah I have the bridgestones on mine and I looked at getting the dunlops but old mate says they are heaps dearer and thought I may as well stick to the same brand I ordered them from Tempe Tyres the other place quoted me just under $900 each so about $1700 for the pair so I'm saving at least $500. Next time I need tyres I will probably get a full set of the new bridgestones the R2's

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So....knowing that I have a problem with power steering temps on track and another Wakefield day booked in next Friday, I've done the obvious thing They are very reasonably priced at $1650, considering they are a big monotube shock, double height adjustable (don't have to change pre-load to change ride height), one way adjustable damping and standard sized and customisable springs if you want something other than what comes with them. They come with 9kg/mm front and 4.5kg/mm front and I went with that as a starting point because I'll add adjustable sway bars too https://justjap.com/products/bc-racing-coilover-kit-ds-ds-infiniti-q50-v37-14-current#description Unfortunately they didn't come with rear strut tops so I've re-used the factory ones which was a bit of a pain. Also, the adjuster for the rear shock will be an absolute nightmare to get at, and while there are extensions in the kit I can't see any way you can actually attach or use them
    • Duncan
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By Duncan · Posted

      I also had 2 bulbs blow at once, years ago in the stagea. made for a fun drive home. The issue was the voltage regulator had failed in the alternator and it was giving 15+ volts. Really, I was lucky all that was fried were the headlight bulbs. So, I'd suggest you check the voltage across your battery terminals with the car running and warmed up. Yes, you will need a multimeter to do so, sorry.
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Good work to think to check that, and thanks for coming back to post up the outcome.
    • Duncan
      98 R34GTT 4k engine stumble

      By Duncan · Posted

      Given it happened suddenly, and when you come on boost, I'd check all your inlet - hose clamps in place and no split rubber or silicone hoses. Even the hard to get to ones near the intercooler. It's possible air that went past the air flow meter is being dumped out a big hole.
×
×
  • Create New...