Jump to content
SAU Community

Recommended Posts

Hi Everyone,

Its that time again and I need to clear out all the parts that I don't require anymore. The reason for the sale is that I have upgraded to full adjustable suspension and the left over motor bits are not required with the RB26/30 setup. All parts were all still functioning when the motors were removed and have all been stored in the garage and now I need the room. Parts are all used and still in great condition. Im located in Adelaide, SA and can ship goods to buyer at his/her expense. All parts are out of a series 1 GTR and GTSt R33!

- oil cooler $30

- air regulator $30

- GTST diff centre $150 (no ring gear)

- generic 12' thermo fan $60

- HICAS steering unit with tie rods $100

- upper camber arms from GTST $20 each

- GTST disc brakes and calipers $ 250 (front and rear)

- gtst intake pipe $10 both turbo intake pipes

- GTR O2 sensors (3) $10 the lot

- vacuum/ water lines $10 (2 sets)GTR

- vac ballast tube $20 GTR

- Blitz blow off valve $70

- trust pod filter $40

- green label air flow meter $40

- rear main crank seal $10

- GTR crank scraper (both) $10

- GTR water pump (no cavitation) $20

- gtst washer bottle $20

- gtst rear camber arms $10 each

- gtst rear traction rods $10 each

- gtst clutch fan $20

- gtst castor rods $20 each

- gtst front LCA'S $30 each

- gtst rear LCA'S $30 EACH

- GTR turbo oil and water line $10

- Gtst full exhaust (mild steel) $100

- gtst A/c lines and condenser $50

- gtst s1 centre grille $80

- bosch 464 fuel pump $10

- gtr thermostats 76.5 deg $5 each (2)

- s1 gtst manual gear set (minus centre plate) $400

- gtst fuel tank $50

- gtst fuel pump assembly $60

buyer to pay for postage of goods!

PICS UP SOON :)

Cheers HULI

FOR ALL THOSE PEOPLE ASKING THE BRAKES ARE IN EXCELLENT CONDITION AND WERE ONLY REPLACED WITH NEW 8 POT AND 6 POT CALLIPERS AND ROTORS.

THE STOCK CALLIPERS AND ROTORS COME WITH THE BRAKE PADS THAT WERE ON THERE AND THE ROTOR THICKNESSES FOR THE FRONT ARE 29.5MM AND THE REARS ARE 19MM.

HOPEFULLY CLEARS UP ANY QUESTIONS

MIGHT EVEN SEPARATE THE SET IF NEEDED!

FRONT LCA'S ****SOLD PENDING PAYMENT****

VACUUM/WATER LINES (1 SET) ****SOLD PENDING PAYMENT****

CLUTCH FAN ****SOLD PENDING PAYMENT****

GTR TURBO OIL AND WATER LINE ****SOLD PENDING PAYMENT****

LOTS OF OTHER EXCELLENT PARTS STILL UP FOR GRABS!

All reasonable offers will be considered on any of the parts above.

LOW BALLERS WILL GET NO RESPONSE AT ALL!

LOTS OF GREAT STUFF STILL AVAILABLE!!!!

PM ON HERE OR MSG/CALL 0400262578

FORGOT TO MENTION THAT I HAVE SET OF GTR DUMP PIPES(WITH HEAT SHIELDS) AND ONE SPARE (WITHOUT) $15 EACH. PUT THE PIC UP BUT NO PRICE OR DESCRIPTION :(

LOTS OF PEOPLE MSGING BUT NO TAKERS. ALL QUALITY USED PARTS!!!

REASONABLE OFFERS ARE WELCOME. AT THESE PRICES THEIR PRETTY MUCH A STEL ANYWAY.

P&H IS BUYERS EXPENSE.

CHEERS HULI

offers are welcome people. all suspension arms $10 each

callipers and rotors $150

need the space, so want all this stuff gone and soon!

CHEERS HULI

help clear out these quality parts. None of the parts has ever been involved in any accident or mistreated. It was all functioning perfectly when removed and replaced by new parts. Need the room in the shed to finish off the car.

CHEAPEST PRICES I HAVE SEEN THESE PARTS ON THIS FORUM..

OFFER ARE WELCOME. SHOOT ME A PM ON HERE OR CALL/MSG ME ON 0400262578

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...