Jump to content
SAU Community

Recommended Posts

Its time to clean out the garage and make some room. Ill continue to add parts up for sale as i go through the boxes, and my rebuild progresses. if you would like pictures drop me a line and ill message or email them to you. All parts are located in brisbane, but im happy to assist with shipping.

RB26 ARP head studs $175
used once in great condition

R34 GTR Sump with diff and tomei sump baffles $400


HKS SSQ BOV's $200
(genuine) Twin hks bov's fitted to alloy pipe

GRID TS dancer 2 $150
4wd Atessa controller brand new never used

Greddy breather tank. $150
(genuine) cooling system breather tank brand new never used

Sard fuel pressure regulator - SOLD

Greddy trust twinBair filters $100
(genuine) as new, fitted but never used

R32 GTR crank +collar $250
crank in great condition. has been balanced, was removed for a stroker crank. comes with genuine nitto crank collar.

nitto crank collar $100

brand new never used

RB26 polished intake plenum , with throttle bodies & spacer plate $300


r33 series 1 dash surround + shifter $80
dash surround and gear shifter surround. includes all buttons , clock, gear boot etc. as pictured

RB26 standard rods $100 set

(2 sets available)

RB26 genuine nissan oil pump $100

(wide drive) was fitted to motor i purchased approx. 10000km use

RB26 R33 GTR Harmonic balancer $100

RB26 head has been damaged on the underside due to detination, was rebuilt and used for less than 40km, happy to strip and part out if anyone needs anything whole head $250

Rb26 pistons 86mm and 87mm sets good for a paperweight $5 each

R34 gtr crank, has stripped the thread for the balancer bolt $50

rb26 block 87mm bore. will need to be bored out to next size $200

happy to seperate girdle and mains if someone is after them.

E.O.I

Nismo 320km/h dash to suit R33 GTR odometer 120,000km black face. comes with white el dials that can be fitted.

Apexi EL gauges - 60mm, white faced. comes with control box, all witing and sensors. in origional boxes. oil pressure, boost, water temp.

Various other external motor pieces for sale please feel free to ask if there is something in particular your chasing.

Link to comment
https://www.sau.com.au/forums/topic/431912-shed-clenaout/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...