Jump to content
SAU Community

19" Rims

Aftermarf

By Aftermarf,
in Western Australia

 Share

Recommended Posts

Aftermarf Enthusiast

Aftermarf

Posted
  • Author
Posted

Well I went to tyres an more in port kennedy an there Spose to no a lot about tyres an stuff an they said I'm not going to be able to but them on coz it's a diff offset by 20mm he told me best bet is to get 20-25mm spacers.... I was thinking change tyre to 265 coz there 275 but. Don't want to get everything an it fails! :( I seen a car that was selling on the forums had them same size an everything so it's possible

Link to comment
https://www.sau.com.au/forums/topic/433452-19-rims/#findComment-7073590
Share on other sites
Hank Scorpio Grand Master

Hank Scorpio

Posted
Posted (edited)

As long as the width and offset of your wheels is correct and you run a 225/35R19 tyre at the front and run the same on the rear or either a 255/30R19 or a 265/30R19 tyre you'll be fine.

Edited by Hank Scorpio
Link to comment
https://www.sau.com.au/forums/topic/433452-19-rims/#findComment-7074173
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      R34 GTR Speedo Drive , sensor type ?

      By Butters · Posted

      Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • Duncan
      spot the stagea

      By Duncan · Posted

      roof rail delete used to be a thing, they were made locally for a while too
    • AnimalGarage
      spot the stagea

      By AnimalGarage · Posted

      I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • AnimalGarage
      Can you mount the ATTESA pump in other locations?

      By AnimalGarage · Posted

      According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...