Jump to content
SAU Community

Wtb Rb26/rb25/rb20 4Wd Engine Mounts And Engine Brackets, Stock Rb20/25 Turbo Setup

Mikha1

By Mikha1,
in Wanted to Buy

 Share

Recommended Posts

Mikha1 Collaborator

Mikha1

Posted
Posted

Hi, as title states, im after the following:

4wd nissan RB engine brackets and mounts, sec/hand.

R32GTRBRACKETS.jpg

Kelpro_Nissan_Sk_4d9c11eb9ad6f.jpg

Rubber mounts dont need to be the best. willing to spend about $100 give or take condition.

sdc10879e.jpg

Stock Rb20/25 turbo setup with all oil/water lines, outlet elbow and actuator. Needs to be in good working condition, willing to spend about $100 for an rb20 one and $150 for an rb25 one, give or take condition.

Dump pipe and manifold not required.

Please PM me as i rarely check this thread

located in Western Sydney, Fairfield area. 2165

Will pay for postage.

Thanks. shoot

Mikha1 Collaborator

Mikha1

Posted
  • Author
Posted

Fail. Not sure how to edit original post

Hi, as title states, im after the following:

4wd nissan RB engine brackets and mounts, sec/hand.

Rubber mounts dont need to be the best. willing to spend about $100 give or take condition.FOUND

sdc10879e.jpg

Stock Rb20/25 turbo setup with all oil/water lines, outlet elbow and actuator. Needs to be in good working condition, willing to spend about $100 for an rb20 one and $150 for an rb25 one, give or take condition.

Dump pipe and manifold not required.

Please PM me as i rarely check this thread

located in Western Sydney, Fairfield area. 2165

Will pay for postage.

Thanks. shoot

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • BASHERnissan
      TPS voltage RB25DET

      By BASHERnissan · Posted

      Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Yeah, I don't believe the M35 uses a deadhead system.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      Have you done your thinking backwards? 3 bar, 43.5 psi pressure drop being the presumed specification for an injector, means you need 3 bar upstream when they are firing into atmospheric pressure, and more upstream pressure than that when on boost (you add your boost to your rail pressure to maintain 3 bar across the injector) and you need..... less pressure upstream when you have vacuum in the manifold. So, presuming that you're idling at -10 psi, then you only need ~23 psi in the rail. I realise that I did not need to say all of that to you specifically Matt, once you'd realised your mistake. It's mostly there for complete clarity for others.
    • Dose Pipe Sutututu
      RB25 Drama's

      By Dose Pipe Sutututu · Posted

      Have you reached out to the guys at Spool Imports? They are a Ross dealer, I can imagine they would have the rings just sitting on the shelf (I could be wrong).  
×
×
  • Create New...