Jump to content
SAU Community

Recommended Posts

LOCATED IN CANLEY HEIGHTS 2166, SYDNEY

PREFER NOT TO POST

PLEASE CONTACT VIA SMS ONLY - 0426876899

LOWBALLERS WILL BE IGNORED

PRICES NEGOTIABLE IF MULTIPLE ITEMS ARE PURCHASED

Parts i have for sale.

4 x standard turbos out of a BNR32 93' (needs rebuilts but all the parts are there. minot shaft play) - $60EA

2 x high flow turbos out of my old BNR32 (needs rebuilts but all the parts are there. minot shaft play) - $80EA

BRAND NEW aftermarket FMIC to suit gtr. 600x300x100 - $260

OEM injectors BNR32 93' - $220

OEM coilpacks BNR32 93' - $125

OEM FMIC + PIPING BNR32 - $200

OEM FRONT STRUT - $100

OEM intake piping - $230

EXEDY HD Clutch out of BNR32 - $350

still has plenty of meat, ive upgraded to a button and no longer need. rated to 400kw

APEXI air filter x 2 suite RB26 (larger sized) - $80ea or two for $150

BRAND NEW APEXI triple stand up guages - $190

RB26DETT LONG MOTOR - $1300

requires, turbos, sump. rest of the engine is there. ready for your RWD rb26DETT conversion.

engine has good compression and i would put it into my datsun. however i just blew all my money building the GTR.

DO NOT offer priced over the phone. come and have a look first. no one likes a first call haggler.

SIMMONS V4 17x8F/9R CHROME 3" LIP. mesh painted black. - $2100

Wheels in very good condition and will come with tyres with about 60% one tyre will need replacing. comes with SIMMONS centre caps.

ADVAN RG 17x8.5+35 all round - $1300

gold in colour with blue advan label round the wheel. wheels in great condition all round. period correct for R32 GTR's. Will come with 70% pirellis all round

AKEI RPF1 SILVER PAIR 18X9.5 +15 - $650

Wheels are in pretty much new condition. not a single scratch on the front face. brand new pairs are going for around $800.. and they look pretty much the same as mine..

BRIDE CUGA PAIR - $750

Great condition. has only ever been in my room. ive actually never fitted them on to the car since i bought it second hand so they are pretty schmick. no rails included

Link to comment
https://www.sau.com.au/forums/topic/434974-skyline-parts-for-sale/
Share on other sites

ADDING TO LIST

R32 GTST M SPEC SIDE SKIRTS IN WHITE - $120

GOOD CONDITION, NEEDS A CLEAN

BNR32 CATBACK TWIN PIPE 2 1/1" PIPES, - $100

nice note, well built, ive switched to single and no longer need this. its collecting dust and taking up too much room. should suite gtst's

btw, how do i edit my initial post? :( new here..

it doesnt have the little edit option at the bottom of the post

Edited by nltd

im trying to edit first post cos this question is being asked alot.

please be advised these seats are NOT genuine. i dont think anyone who is sane would sell genuine bride cugas for $750 LOL

colour scheme - BLACK/GREY/WHITE

please text with what item you would like photos of

ive replied to all sms's by now. please be advised im at work fr 830 am till 7pm. all pictures and responses will be sent once im home.

those asking for photos of enkeis. as stated in descriptin. they are practically new. please just google the photos. they are stored away in a box in the garage and require alot of effort to pull out unless someone wants to buy.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...