Jump to content
SAU Community

Need Help On Holset Hx35W On Rb25

Rb25detvlt

By Rb25detvlt,
in Engines & Forced Induction

 Share

Recommended Posts

Rb25detvlt Collaborator

Rb25detvlt

Posted
  • Author
Posted

does any one no how much psi the standard oil feed runs at also could it be pumping to much oil into that an forcing oil out the rear seal will drilling a bigger hole in the standard line oil feed line an bolt help or hinder it... is it possible to have a damaged rear seal but still have no shaft play

hypergear Grand Master

hypergear

Posted
Posted

No, it can never have too much oil that forces out of your rear seal from your RB25det pump. Because the tolerances between the bearings, bearing housing bore and shaft, limits the amount of oil flow.

If the turbocharger is flooded as in if there is a oil drain problem in which stops the oil from getting out, both compressor and turbine end seal would be leaking oil (unless it is and you've only noticed the smoking end).

In your case, because the compressor side has a collar that spins that throws away excess oil directed towards it, so the compressor end is dry. Means the bearing housing is not flooding there for you don't have a oil drain issue.

If there isn't enough oil and oil pressure going to the bearings which I definitely know the Stock oil feeding line and benjos don't. Then the shaft has no centripetal support, the rear end (heavy end) would be vibrating it self in an orbit starting with chewing out rear seal splattering oil.

^^^

Above opinion is only suited for a proper Holset turbo, if what ever installed is a knock off copy then the matter could be at a newer level of complication.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      New lightweight, square wheel/tyre combo for the E90

      By PranK · Posted

      Ok cool, because I do have some OEM BMW options for light(er) wheels. 17x8.5 M Sport wheels are 11kg and I could put 255's on them. Maybe that's an initial test.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, in the effort of pulling apart airboxes and testing enclosures to see if this aids in MAP loss at WOT I noticed: 1) The ducts up the OEM intercooler holes from the front bar help IAT drastically, whether the pod is shielded from the engine bay by an airbox missing a lid, or an airbox WITH a lid. Plus you get more induction sound without the lid. Having half the airbox (with no lid) acting as a barrier to the headers seems to help. 2) For shits and giggles I checked the TB. This was full pedal travel. This is actually full travel of the TB. Photos aren't perfect, but there was definitely an amount of play in it and it wasn't against the stop. After much swearing and adjusting the pedal, I realised that the cable is actually too long for the skyline pedal travel to fully articulate it. Having the pedal adjusted so WOT was actually hard open on WOT resulted in an idle of 3500rpm. As an aside, this was also the TPS registering at 3.1%. I removed the above to give the pedal enough travel to actually fully open the TB. I now get a satisfying 'thonk' on full open and full closed which you can hear pumping the pedal as it hits the TB stops (with the bonnet open and intake back on). Luckily for me, the screw screws into a raised metal boss under this plastic piece that is now acting as the new throttle stop. I've gained about 20mm (ish) of pedal travel and I can move it maybe a mm or two post open-thonk before it's hard against the stop. After all of this I did a bit of road tuning because a 102MM throttle is sensitive. The difference between holding an 950rpm idle and instantly stalling is about 0.4% of TPS movement. Will that help? I suppose it can't hurt. I set 'closed' point back to where it was, I can definitely feel the extra pedal travel that is needed to actually open the TB fully. But this morning I dropped the car off at Paint Jail again, so who knows when this will re-eventuate out to see if it helps with the top of the dyno hitting a ceiling.
    • Kinkstaah
      Looking for someone with a R34 front bar

      By Kinkstaah · Posted

      Take heart that everyone else seems to have found a way. The OEM S1 indicators do slot in pretty firmly. It may simply be a case of having them sit slightly looser and nobody actually ever noticed this when attempting to remove a indicator from a JSAI bar :p
    • GTSBoy
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By GTSBoy · Posted

      If the original NA ECU has a separate TCU then you are going to need to reroute wires that used to run between the trans and the TCU to the appropriate (1 to 1 equivalent) pins on the ECU. Other than that, it should work. Look up posts by @Kinkstaah on the subject.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      So the stagea was a series 2 neo det with tiptronic auto. (I have the transmission aswell) and has integrated tcu in the ecu. I'm hoping to use the entire stagea ecu, engine and auto harness. 
×
×
  • Create New...