Jump to content
SAU Community

R33 Gtr Bosch 044 In Cradle Ready To Drop In, R33 Exhuast Parts And Standard Cooler R33 Gtr

asps91
 Share

Recommended Posts

asps91 Rising Star

asps91

Posted
Posted (edited)

Hi guys, i have the following for sale:

-bosch 044 in cradle ready to drop into a r33 gtr. Very limited use form a few days (didnt even make it onto the dyno before i decided to go for a bigger fuel set up) this would be good up to about 350rwkw on e85 and 400+ on pump. $150 ono

-r33 gtr mines front pipes (same dimmensions as mines so im oretty sure they are) they have surface rust but that obviosly doesnt effect preformance haha. $100

-80mm rs*r catback exhuast (including high flow 3 inch cat) to suit an r33. $200

-r33 gtr standard intercooler and piping into the engine bay (cooler has a dent on the bottom and a few nicks in the fins) this wont effect preformance. $150

All prices are ono and i am located in sydney. Call or pm. 0404 111 174.

Thanks!

Edited by asps91
mic087 Community Regular

mic087

Posted
Posted

Can I get a picture of cooler and piping? I'm rather keen on it depending on the condition of the fins..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
×
×
  • Create New...