Jump to content
SAU Community

Recommended Posts

whats your thoughts on the unichip in an r33 gts-t auto?

i got a few mods at the moment

catback 3"

stage 2 shift clutch

airpod

FMIC

apexi boost controler old one but works good

series II motor

making 187rwkw

going to put on

fuel pump (prob GTR have a VL standard one is that anygood or chuckable?)

3' dump pipe + front pipe

high flow cat

replace plastic pipe with 3" stainless AFM to turbs

and a unichip last bit

hoping to put out over 200rwkw might push for 250rwkw but then injectors and new turbo are the issue and manifold

but main issue is how are people going with the unichip?

was gonna go the e-manage but no tuners in adelaide except rpm and they only have the program they aren't that good with it ( from what i heard) but there good no probs there

Link to comment
https://www.sau.com.au/forums/topic/44362-unichip/
Share on other sites

got two feet for launches its not hard better for it, like weather changes will stuff up the stall converter

pFC doesn't work with autos, emanage are having probs with autos and no tuners so no option there

oil cooler for trans was thinking that, but don't skylines come out stock with em? i have a cooler on the front of the radiator, looks like a stock trans cooler, i could be wrong though

Link to comment
https://www.sau.com.au/forums/topic/44362-unichip/#findComment-906968
Share on other sites

You don't put oil in your trannie but yeah, it should have a cooler out front there. Is it between the radiator and the front mount?

I don't know but isn't the cost issue with Unichip the tuning rather than the install? Ie hours and hours of tuning necessary.

Link to comment
https://www.sau.com.au/forums/topic/44362-unichip/#findComment-907032
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...