Jump to content
SAU Community

Fs Cheap Daily! Holden Barina 6 Months Rego $990 Ono

GTR_JOEY

By GTR_JOEY,
in New South Wales

 Share

Recommended Posts

GTR_JOEY Grand Master

GTR_JOEY

Posted
Posted

Hey guys, up for sale is my 1993 Holden Barina 5 door (white) 1.3L automatic

I have acquired a VT commodore for cheap so its time to get rid of the 3rd car

125,000km on the clock - wouldn't pay too much attention to that

The good:

6 months rego (January 2015)

Major service just completed including

-timing belt

-engine and transmission oil changed

-air, fuel, engine and transmission filters changed

-spark plugs changed

-changed the front pads and has new brake fluid (also comes with rear pads, but I didn't change them as it didn't need it)

-rocker cover gasket changed

AC is cold

Awesome on fuel, approx. 8L of fuel per 100km around town

Mechanically its sound and hasn't failed me in the time ive had it

The bad:

The body has a few dings in it but nothing too bad

The tappets are a bit loud during start up until the engine is warm when the quiet down. (I have personally adjusted the tappets) Thicker oil should quiet them down

There is a small oil leak from engine, not sure where from as I was never concerned enough to worry about it

Only chasing $990, Awesome little daily

Located Prestons

0432528844 or PM for pics

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...