Jump to content
SAU Community

Recommended Posts

Whoa sozz i got a bit carried away with that one.they are all side feed injectors.

Hey i want to know would they be a straight fit for some SARD 550cc Injectors Side feed, High Impedence. http://www.greenline.jp/catalogue/bcpartli...=R33B&intake=FI these guys have some injectors but they require some injector collars.And what i was thinking was why would they make them for the rb25det and they need injector collars to fit.:)

Thanks,Craig.

[email protected]

Those injectors require more than collars I believe, they need to be modified so they can fit in the rail from what I remember, those mods are best done by an engineer. You can use the fitment kit on them though.

RX7 injector prices vary, it's simply a case of checking around because prices vary considerably, try out of the way places.

So are you definently sure that these would fit the SARD 550cc Injectors Side feed?Have you had any experience with them?what are your reasons.

The only reason that im asking is cause im thinking about buying the injectors and need to know for caertain not halfway certain.:D

So are you definently sure that these would fit the SARD 550cc Injectors Side feed?Have you had any experience with them?what are your reasons.

The only reason that im asking is cause im thinking about buying the injectors and need to know for certain not halfway certain.:D

So are you definently sure that these would fit the SARD 550cc Injectors Side feed?Have you had any experience with them?what are your reasons

The only reason that im asking is cause im thinking about buying the injectors and need to know for certain not halfway certain.:D

I am 98% sure that that is the injector I think it is, however I would prefer a part number in order to be 100% sure. Assuming it is the injector I believe it is, then the following holds:

It will first need modifying by an engineer, both the lower filter assembly and the small flange on the aluminium pintle cap. I had a set of SARD type 550cc injectors only a few weeks ago, so I know exactly what to do. The flange has to be modfied precisely because it has to hold the lower o-ring in place, care must be taken not to damage the lower filter assembly too because there is no replacement part available. When that has been done, the fitment kit gets added, then you can install them (ideally they should have a flow test first though). They will be high impedance but different connector (included in the kit I have).

I will email you, I can make them direct fit with the kit installed.

Here is the part number u wanted in an email i got from greenline.

Hi,

The part number is 63508. Alternatively 63509 can also be used.

Please let us know if you require further information.

Kind regards,

Jason

Greenline Motorsports

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...