Jump to content
SAU Community

Recommended Posts

Almost feels like an old dodgy carby! Idles rough as shoots fuel out the back and get even rougher if I touch the throttle and stalls. I have driven a few times when cold, if I stop instead of rolling through say a giveway sign, the car will stop and cant be started for a few mins, only then holding the throttle flat (like a carby) will it start again. Other than that any attempts earlier it'll just keep winding over and getting too much fuel. 120psi across all 6 so its getting tired but doesnt use or blow smoke.

Link to comment
https://www.sau.com.au/forums/topic/449351-rough-idle-on-cold-start/
Share on other sites

Also to add to my other post about rough, sluggish between gear changes at times, slowly feed the loud pedal its normally ok, but mash it and grab 3rd it runs rough like its dropped a cylinder untill I back right off, let it coast then re apply the throttle

It was doing it with my stock coil packs, now ive put ls1 coils on and still doing it. .8 for the plugs. No smoke test as yet, only an issue really when cold or occasionally after a flogging. My afr gauge reads fine however I suspect the fuel pump may be a problem

Are you using a real wideband or those stupid narrowband gauges that show absolutely nothing but flashing lights.

By the way, LS coils will need more ignition dwell time to work properly. Given the fact you're using a stock ECU I am under the assumption there isn't enough spark generated

  • 3 weeks later...

45psi base. Thing is, first cold start is shit as any throttle input it runs even rougher and sometimes stalls and will crank over for about 15 seconds then fire like its flooded! Fuel pump appears to work fine as its holding 10.4 afrs at full throttle. Ive changed afm cas tps ecu fpr and still doing it. Does it occasionally between 2nd and 3rd shits where I have to back off coast for a bit and re apply throttle to run smooth again

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ironically the GTT was quite reliable in the 7 years of ownership. From memory I've only had to replace a radiator and coilpacks out of inconvenience 
    • Yes I can see how that would put you off HFM, especially with the price of good quality brake fluid. From what I understand it as you say the BM50 is the standard BMC for a R32 GTR, I must admit I would like to go far a Genuine Nissan BM57, but lack of cash prevents that at present. With the price being so close between the genuine BM50 and BM57 a BM57 New it seems a better choice as you gain that 1/16 bore size with the BM57, I would be interested in how much difference you feel with the BM57 fitted. I am going to take SteveL's advice in the short term and see how much actually comes out of that proportioning valve vent and save up for the Genuine Nissan part. Thanks for clarifying the HFM failure
    • Thanks mate. I just got the post inspection 1/2 done from state roads when the starter motor packed up, either that or the car alarm system is having trouble.  OEM part number 23300-AA112.
    • Hi, I though I was coming to an end in finding a replacement starter motor for a rb25de neo. I came across a starter motor from Taarks and a message below stating: Direct fit. 11 Tooth count. All below part numbers have been superseded to 11 teeth. Can some body shed some light on going from 8 teeth to 11 teeth apart from 36-month / 25,000 km warranty for passenger vehicles to 12 Month Warranty. Compatible with the following Nissan part numbers: 23300-20P00 23300-20P01 23300-20P05 23300-20P10 23300-20P11 23300-AA111 23300-AA112 23300-AA300 23300-08U10 23300-08U11 23300-08U15  
    • Low battery? Maybe check capacity? I know first-hand, on BMWs if your battery drops below 80% capacity, it starts causing strange issues.
×
×
  • Create New...