Jump to content
SAU Community

Recommended Posts

hey guys,

well after all me saving up i finally have the money (and can get half decent insurance) to by a GTR!! :cheers: btw im in perth so the car has to be in perth. As the subject suggests im after a 32 GTR pref with close to or less than 100000K's. Also with minor or no mods but i can be flexible on that. looking at the $25-32K mark. plz contact me via pm, email [email protected] or sms me on 0422906956

cheers

Link to comment
https://www.sau.com.au/forums/topic/45098-wtb-r32-gtr-in-wa/
Share on other sites

Good GTR's in WA are a little thin on the ground atm.

Don't believe all the horror stories, some of the best GTR's I have seen for a while have been 89's and at the end of the day , the best they are going to be is 10years old.

There are at least 2 other people I know chasing GTR's in WA so good luck.

Cheers

ken

Link to comment
https://www.sau.com.au/forums/topic/45098-wtb-r32-gtr-in-wa/#findComment-919911
Share on other sites

I am selling my 32, I will refund the cost of the flight to come up and see the car and am willing to go halfs in the price of shipping the car to any where in australia. See what you think, will have pics tomorrow.

89 32 GTR.

Silver,

60000km,

Unbelivable Condition,

Car has never been modified,

Except for 3 inch cat back exhaust &

Turbo Timer.

Just had full service including brakes.

$29 500 ono

Car is located on Gold Coast.

E-mail me for more info [email protected]

Thanks

Link to comment
https://www.sau.com.au/forums/topic/45098-wtb-r32-gtr-in-wa/#findComment-920530
Share on other sites

$29,500! for an 89?

I have an 89 in very good cond and is in rare Burgundy with some minor mods and a brand new exedy twin plate I would let go for that and I am in WA.

Cheers

ken

Link to comment
https://www.sau.com.au/forums/topic/45098-wtb-r32-gtr-in-wa/#findComment-921097
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...