Jump to content
SAU Community

Recommended Posts

Originally posted by inark

question:

if its off a different car will it still work on a different type? or are they designed for that car only?

universal; all it does is working with your ecu, adjust different rpm range of a/f mix.

installation guide comes with wiring diagram connect to factory ecu, very easy installation, however use dyno tune to get best result.

check http://www.apexi-usa.com/electronics_safc.asp

Link to comment
https://www.sau.com.au/forums/topic/4515-apexi-s-afc-x2/#findComment-70892
Share on other sites

Originally posted by inark

how old are they? cause nengun sells em new for 512 including delivery.

computer does not run out like tyres or something..

off s15 one for 3000KM

off R34GT-T for 1000KM, both are upgrade to PFC

cheers!!

Link to comment
https://www.sau.com.au/forums/topic/4515-apexi-s-afc-x2/#findComment-70897
Share on other sites

Originally posted by inark

hmmmm... dunno... steve said it would be a good idea... i'll get it anyway... if i dont need it i'll sell it

sorry about it, was in somewhere has very poor coverage.

you can pm me or email me.

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/4515-apexi-s-afc-x2/#findComment-71233
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...