Jump to content
SAU Community

Recommended Posts

Ok so I'll start at the beginning my R34 Gtt series 2 had the exhaust wheel snap off the turbo, as I am on a budget I bought second hand standard turbo, running standard boost it drove fine for about a week, then all of a sudden I noticed a noise like a squeal and my boost dropped off, so immediately stopped, it hasn't over heated nor is the oil creamy so was hoping someone might have some idea don't want to pull off the head if it's just a cracked turbo internally is there some way of checking I noticed aswell that I can idle the car no squeal or anything seeming wrong but if I rev I'm getting boost but when it hits max it drops off and I get exhaust fumes out my radiator, any help or tests that I can do would be greatly appreciated I'm on a budget but if it comes down to it I'll pull it off the road until I can scrape enough coin to do turbo and head/ gasket if required but that'll take a long time to save

Link to comment
https://www.sau.com.au/forums/topic/452443-need-help-r34-engine-issue/
Share on other sites

Sorry should of been more specific the squeal was the split in the header tank and I did use brand new gaskets etc when fitting the turbo, I'm more looking for a test to work out wether the exhaust gasses are entering the cooling system from the head or internally in the turbo

Ask at Supercheap or Repco. Combustion Leak Tester.

You should be able to buy a kit that will tell you if there is Exhaust gasses in your coolant by the change of colour. (blue to yellow)

Instructions will be on the kit and should take less than 20 minutes.

You can also do a quick test by removing your radiator cap to see if your getting bubbles.

If so:

It will be the head/head gasket.

Edit: Not to say your Turbo isn't screwed also

Edited by Sinista32

I am getting bubbles in the radiator that's how I know that the exhaust is leaking I'm just confused as I thought the head/ head gasket would've allowed coolant into the oil or vice versa ill do a compression test and see what I get, do you know what it should be reading if the engine is within spec, and the only reason I'm suspecting turbo at all is because it's the only thing that's changed and is oil and water cooled so I thought there's a possibility that it could cause exhaust in coolant should a seal fail or housing crack, and because it idles fine but when I accelerate the boost guage hits 7 then drops straight to zero so stops boosting

I'm always surprised how people think a head gasket failing will always mix coolant and oil.

Looking at a gasket it's the least likely scenario. There's heaps of coolant galleries and not many for oil. So typically a blown gasket leaks coolant only.

For now the leak is small. Keep driving and you will eventualy see oil in the water. Second hand turbs never a good idea. As for turbo causing gasses in the radiator - no.

So there is no chance that the turbo cracked internally and is feeding exhaust gasses through the cooling section of the turbo out into the cooling system, and ill do compression test ASAP and post results, in order to keep driving the car ill have to get new radiator because too tank on radiator split open so it would've had to over pressurise the cooling system

I'm always surprised how people think a head gasket failing will always mix coolant and oil.

Looking at a gasket it's the least likely scenario. There's heaps of coolant galleries and not many for oil. So typically a blown gasket leaks coolant only.

I do understand what your saying but wouldn't you still likely get an overheating issue or smoke out the exhaust?

I do understand what your saying but wouldn't you still likely get an overheating issue or smoke out the exhaust?

No. It will overheat when it loses enough coolant. It only creates steam when a fair bit is going through. Small leaks don't show up easily.

That's why there are test kits available for checking for the precede of exhaust in the coolant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Grind them off, drill them out. Repair any rust on the other side. Start again from scratch.
    • Big R34 GTR parts cleanout. I have a lot of stuff collected over the last 14 years and my missus is giving me hard time. Make my life easy.   Nismo GT carbon fibre diffuser fins (discontinued)  NEW  $2900 Garage Defend Stingray canards carbon fibre  NEW  $1300  Top Secret G Force carbon fibre front diffuser  NEW  $2000  Haltech Elite 2500  NEW  $2500  Haltech Platinum Pro R34 GTR   USED  $1400  Apex’I power FC D'jetro + hand controller R34 GTR   USED  $1400  Nissan OEM BNR34 ECU  USED   $1000  HKS EVC 6  USED  $600  Blitz dual SBC ID boost controller.  USED  $350  TRE 255 LPH Fuel pump  NEW  $100  Fujitsubo  Super Ti exhaust  USED  $2700  Tomei Expreme Ti exhaust  USED  $2000  Trust stainless steel front pipe  USED  $1000  Apex’I super suction kit  USED $400  BC BR coilovers  USED  $600  Hardrace front upper camber kit. USED  $300  Garret 2860-5 turbos –  one good, one needs reco USED  $1000  Nissan OEM Toshiba MFD Screen replacement  NEW  $450  Nissan OEM BNR34 Series II front passenger seat  USED (mint) $5000   Nissan OEM BNR34 front bar in TV2  USED  $1000  Nissan OEM BNR34 front lower air spoiler  USED  $900  Nissan OEM BNR34 front lower air spoiler (painted)  USED  $900  Nismo front indicator (clear) USED  $80 Nissan OEM BNR34 radiator  USED $500  Nissan OEM BNR34 turbos  USED  $500  Nissan OEM BNR34 intercooler USED  $800  Nissan OEM BNR34 front swaybar   USED  $500  Nissan OEM BNR34 intake pipes   USED  $400    Also have a square set of uber rare Volk CE28n in 19*10 +22. Not really keen to sell these but make a high enough offer and maybe I will. If you don't know how much these usually sell for don't bother.   PM for pics.  Pickup Chadstone VIC or postage at buyer's expense.
    • Thanks Mate, I did know you could do that but i know there is a pump out there that you can bolt on and it all lines up. I was told about it and then forgot the model, I figure if i am pulling it apart i will just put a new one on 
    • You can also remove the veins from the HICAS portion of your existing pump. 
    • Trying to swap the rear subframe on my R34 and can't remove the L-shaped stay brackets between the front subframe mounts and the sill/chassis. I'm in the UK so rust is a problem. I've used loads of WD40 and then Tunap 103 for days beforehand. I backed off the bolts forward a bit, backward a bit repeatedly for ages to try and avoid snapping. They have all moved a few full turns. The one I've spent most time on has come loose and I can turn with fingers, and it will pull down and push up 2-3mm. But it won't come out. I can tighten it back up and loosen it off again repeatedly but it still won't come out. I assumed there's a captive nut inside but if that's broken loose then I can't understand why I can always tighten the bolt back up - I'd expect it to just spin both ways. Any ideas what's happening here? I can't visualise what's inside there to cause this.
×
×
  • Create New...