Jump to content
SAU Community

Recommended Posts

Needs to go asap to fund fines

It's in good condition bought it off a person on sau

Haven't put it on my car so it's still on my desk

No shaft play

Located between Smithfield and Campbelltown new

Can deliver for a small fee

$250 firm

Link to comment
https://www.sau.com.au/forums/topic/457786-op6-r34-gtt-neo-turbo/
Share on other sites

Hello peanut I need a turbo to get my old car going

In the last years I brought 3 that were advertised in great condition 2 never even got put on the car the other I fitted it to get it from Adelaide to mildura these were 25 turbos I seem that I could never get a bit of luck the cars sat for along time now cause I just lost interest in it has a good strong motor but I done some deal when I brought the front cut cause I was going to get a better than standard turbo and it all turned to shit from there

I've have money right away to even buy a new Garrett bu, but as you know you got to do this and do that

I just want to get the old girl out of the shed its been there that long the fuels turned to turps locked the pump up and ate the little piece of fueline to nothing, I've put a in tank 023 init so that's right

I do relise that these turbos have been used I just need one that's gonna work for a while not sound like there running on the housing or bellowing smoke, the trouble is these r34 and other Nissan turbos are getting old, they always seem to fail first hense emissions in japan

I've the cash if your satisfied I can drive the car for a year or so on 8 to 10 she's sold but but I have to put my trust in you,my car hasn't gone for years after a accident It had wrecked me for 10 I'm egear just to get the thing out of the shed run it and tune it as you can tell it won't be a race car

The rare Garrett off the r34 with the steel wheels I'd like to find but never had any luck when I was sick maybe I could start looking for one of those

If ya got no worries will slip ya the cash asap

Thanks matthew

Hi matt I would like to say that sounds like a pretty crap time you've had

I would like to invite you to look thru the build threads and find my car

The tales of the nightmare 32

Upon reading that you will find that I am trusting and that I wouldn't be selling it blown if i knew about it

I did purchase this off another sau member very recently and I will ask him if I can mention him

But as i haven't physically put this on my car and driven with it I cannot guarantee it. But what I can do is if it gives you problems when it's installed on your car I will give you a refund

Provided you correctly install oil lines and do not over boost it.

Over boosting would cause the rear wheel to shear off and would be obvious upon inspect

How does this sound

Hello.

He bought it off me. Had this turbo on my r34 which I bought 3 years ago. I am the first owner in aus. Removed it as I bought a hypergear turbo.

I had no issues with it. I only had stock boost running through it. I wouldn't recommend more than 12psi due to the nylon wheel In series 1 op6 turbos. This turbo does not have a steel wheel.

Good luck.

Thanks peanut and other fella me computer broke like the car so I stole the kids tablet

I'm not quite sure how to just msg you peanut,I'm sure you have another name seems weird calling ya that,anyway sounds like I've meet 2 cool fellas thanks for the reasurence I've got heaps of shit to get and I really should start to learn how to use these sites better, I got a head injury in that accident so the motec I used to have as a brain is now an old powerfc still works but missing some of the finer points if ya know what I mean

I'm not sure how to pay you can you ad post to vic 3505

I've lost me phone but should find it soon

You can msg me 0429940623 or matt0872@hotmail

Soon as you work out the post I will slip the cash in for ya

When I get some time tonight I'll have a look at ya stuff

Thank you for you help

I've got heaps to ask but over the years I've been fixing these jap cars myself and never saying anything

With how things work today a much smarter approach would be to msg sites like these and find out the problems using shared information I know a couple of skylines inside and out now cause I went ahead and repaired stuff without even a manual so I could of saved a couple of years if I just picked the computer up

Anyway thank you again will speak to ya soon

Yeah. It also depends on how you drive it. Wind it up to 18 if you want. If you're driving to Centrelink down the road and back everyday and never hitting boost for the next ten years then yeah I guess op6 can handle 18psi for ten years!!!!!!!

12psi is a safe guesstimate that allows you to have fun with the car with a lower possibility of a blown turbo.

Again it depends on how you maintain/drive your vehicle. Take it with a grain of salt or make statements with no evidence on the Internet. As long as your happy that's what it's all about in the end.

Hey matt this is the easiest way to send the photos

Here's my packing it up for ya

post-108512-14359099662734_thumb.jpgpost-108512-14359099813916_thumb.jpgpost-108512-14359099930329_thumb.jpgpost-108512-14359100258391_thumb.jpg

Getting shipped off to the post office

post-108512-14359100433022_thumb.jpg

And here I am I the post office

post-108512-14359100617409_thumb.jpg

Hope it arrives safe.

You should have the tracking number and it's insured aswell

Hope it serves you well

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...