Jump to content
SAU Community

Gtr33/34 Ohlins Mines Coilovers,serial 3 Gearbox, Rb 26 Head,block,new Cp Pistons And Eagle Rods, Yoko Semis


Recommended Posts

Selling off my spares, track car is going good, I hope I wont need them

Item 1, Ohlins Mines adjustable coilovers, front part #CT5-S0100-70,Rear CT5 S0200-70 with Mines revalving,Mines ESTA springs. Mines tuning house is reknown for drivability and comfort. GTR33 did 1:46 at Phillip Island,I have bought Ben's ( Racepace founder) Tien RS/RA. Hope the car can go faster.

$1500

Item 2 .GTR33 serial 3 gear box out of a 97 model with 65000km. my OS Giken closed ratio is going good,no need to keep spare

$1500 ono

Item 3. RB26 block GTR33 crank, matching girdle , machined, balanced, cleaned,deck,etc.etc with New CP Pistons 87mm and Eagle Rods. $2900.

Item 4 RB26 GTR33 stock rebuilt head ready to go into the above Item 3. $1600 Can arrange assembling

Item 4 number of Yoko A050 265/35/18 good for practice and sort out car,2 Kumho S70 255/40/17 40% thread .$30 each. pick up from Braeside 3195

Best to sms/call Alex 0433878905

post-50742-0-67787800-1440988962_thumb.jpg

Bill will have first dip with long forged motor package going into a GTR34.

Got a pair of HKS 2530 with dyno time only, I have gone single turbo. $2200, no actuators.

Brand new ATS treble carbon push type clutch still in box from Negan Japan.. cost $4200 landed. best offer over $3500. I have put a Nismo super copper mix, excellent clutch on my track car.

Any proof that 2530's are new apart from dyno time, Are they recently bought with a reicept?

Where are the Wastegates?

I have gone single for my track car,it is a lot easier to work on, actuators were sold ,Bought these off a mate who also gone single,sorry no receipt as I did not buy them from HKS dealer CJ Motors. I have also put a pair of 2530s replacing a T88-38GK to make one of my GTR33 street legal in Victoria.350kwaw on 98 pump fuel. The core is Garrett -5, 2530 has its own HKS housing which flow better.that the only difference

  • 2 weeks later...

Got a 300zx 5 speed gear box in very good condition $800, gear set is same as RB 25 box, I have gone with RB25 box conversion with Speedtech close ratio gear set. Looking for a broken RB25 box to swap gear set over as spare box. Anyone in Melbourne has got one?

Alex 0433878905

  • 2 weeks later...

looking for Ikeya sequential shifter for GTR 33 5 speed box with OS Giken gear set and Front lower control arms with roll center adjustment spacers. Hardrace brand or Ikeya

  • 2 weeks later...
  • 1 month later...
  • 3 weeks later...

got a set of upper and lower Ikeya front control arms from Bill. Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...