Jump to content
SAU Community

Gtr33/34 Ohlins Mines Coilovers,serial 3 Gearbox, Rb 26 Head,block,new Cp Pistons And Eagle Rods, Yoko Semis


Recommended Posts

Selling off my spares, track car is going good, I hope I wont need them

Item 1, Ohlins Mines adjustable coilovers, front part #CT5-S0100-70,Rear CT5 S0200-70 with Mines revalving,Mines ESTA springs. Mines tuning house is reknown for drivability and comfort. GTR33 did 1:46 at Phillip Island,I have bought Ben's ( Racepace founder) Tien RS/RA. Hope the car can go faster.

$1500

Item 2 .GTR33 serial 3 gear box out of a 97 model with 65000km. my OS Giken closed ratio is going good,no need to keep spare

$1500 ono

Item 3. RB26 block GTR33 crank, matching girdle , machined, balanced, cleaned,deck,etc.etc with New CP Pistons 87mm and Eagle Rods. $2900.

Item 4 RB26 GTR33 stock rebuilt head ready to go into the above Item 3. $1600 Can arrange assembling

Item 4 number of Yoko A050 265/35/18 good for practice and sort out car,2 Kumho S70 255/40/17 40% thread .$30 each. pick up from Braeside 3195

Best to sms/call Alex 0433878905

post-50742-0-67787800-1440988962_thumb.jpg

Bill will have first dip with long forged motor package going into a GTR34.

Got a pair of HKS 2530 with dyno time only, I have gone single turbo. $2200, no actuators.

Brand new ATS treble carbon push type clutch still in box from Negan Japan.. cost $4200 landed. best offer over $3500. I have put a Nismo super copper mix, excellent clutch on my track car.

Any proof that 2530's are new apart from dyno time, Are they recently bought with a reicept?

Where are the Wastegates?

I have gone single for my track car,it is a lot easier to work on, actuators were sold ,Bought these off a mate who also gone single,sorry no receipt as I did not buy them from HKS dealer CJ Motors. I have also put a pair of 2530s replacing a T88-38GK to make one of my GTR33 street legal in Victoria.350kwaw on 98 pump fuel. The core is Garrett -5, 2530 has its own HKS housing which flow better.that the only difference

  • 2 weeks later...

Got a 300zx 5 speed gear box in very good condition $800, gear set is same as RB 25 box, I have gone with RB25 box conversion with Speedtech close ratio gear set. Looking for a broken RB25 box to swap gear set over as spare box. Anyone in Melbourne has got one?

Alex 0433878905

  • 2 weeks later...

looking for Ikeya sequential shifter for GTR 33 5 speed box with OS Giken gear set and Front lower control arms with roll center adjustment spacers. Hardrace brand or Ikeya

  • 2 weeks later...
  • 1 month later...
  • 3 weeks later...

got a set of upper and lower Ikeya front control arms from Bill. Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi all, I’ve just finished fitting the timing belt on my RB25, following the standard procedure: rotate the crank twice, release the tensioner, then tighten it down. The belt feels tight, and you can see that clearly in the picture below I’ve heard some people say it’s actually better for the belt to be slightly loose rather than too tight, as excessive tension can lead to snapping. So that’s in the back of my mind. What I’m seeing is this:  • At idle, the belt looks fine.  • But when cranking and especially when revving (around 3–4,000 RPM), there’s a momentary flap/flex or flicker in the belt, which I’ve tried to capture in the video. So my question is — based on what you see, is this slight belt movement something you’d consider normal, or am I just being OCD? Could this amount of movement cause sync issues? Or is it just a harmless bit of flex under load?   from what I know belt flap and flex is expected when crank spins up and pull cam with it Would appreciate any thoughts or similar experiences.     IMG_7656.mov IMG_7657.mov
    • I've replaced the front brakes of my NA to 324 brembos and 350z calipers: i'm going for 225/40-18 up front and 245/35-18 in the back. I have Rays 7.5*19 ET35(225/35) in the front with 5mm spacers otherwise the calipers "lock up/ won't rotate". When i use the calculator i come up with 8*18 ET30 for 225/40...... but not sure i get problems with the calipers. Anyone riding around with 18 inch. that can confirm "that it'll fit"? In the back it's 7.5*9 ET30 (245/30) with the 5mm spacers, but there is no problem with the standard small brakes, so i want to take 8.5*18 ET25 (245/35).
    • Lol.. but then.. always come back to a JDM..
    • Glad to hear. If possible, get your tuner to check air's to make sure everything is still where it should be.
    • The problem with FB/Insta/Reddit etc comments relating to cars is simple. You get to ask a question once, and get one round of replies. For things that can actually be answered in a few lines of text, once, it's fine. After 6 hours, your original question is lost to the void. There are no follow ups, additional questions, anything. No project car is ever such a simple list of questions to ask. You need discussion.
×
×
  • Create New...