Jump to content
SAU Community

Recommended Posts

Howdy.

Been unto toyotas most of my life, mostly older Corollas. Recently bought an AW11 but with 2 kids it just wasn't practical.

Anyway got offered a pretty good swap for a very tidy r33. The rest is history.

From what I know (which isn't much) it's a series 1.5 Rb25det. Mods are pretty basic, lowered springs, 400R front bar, Tommy Kaira wing, Nardi wheel, drift teks, boost tee, turbo timer, extreme HD button clutch, Nismo gear knob.

Here it is next to my aw11 the day I swapped.

post-141360-0-53395600-1443332743_thumb.jpg

After boosting it around for a bit pretending I didn't like it.

post-141360-0-81636400-1443332854_thumb.jpg

Actually really like the car. More than I expected. Not sure if it will turn into a love affair yet ;)

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/459994-new-r33-owner/
Share on other sites

It's definitely fun. But a different fun. Will take a bit to get used to the power and size. I know I'll miss the aw11 a lot but there's definitely worse things I could have traded for.

Just need a smaller rear spoiler.

Link to comment
https://www.sau.com.au/forums/topic/459994-new-r33-owner/#findComment-7609841
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...