Jump to content
SAU Community

Exedy Heavy Duty Cushion Button Clutch & Flywheel

Borci88
 Share

Recommended Posts

Borci88 Veteran

Borci88

Posted
Posted

I have for sale an Exedy Heavy Duty Cushion Button Clutch & Lightened Exedy Flywheel. The clutch has done 2,000kms including run in on the dyno, I pulled it out when I rebuilt the engine and a good price on a Coppermix came up so I purchased that. Clutch has very very little wear and has been sitting in storage for the last year. Flywheel still has very visible machining marks from machining when the clutch was installed to show that it's done very little kilometres.

This clutch is a Pull clutch and is to suit late model R32 GTR and all R33 GTRs.
Item is located in south eastern suburbs of Victoria, also willing to post.

post-70634-0-38834700-1455874840_thumb.jpg

post-70634-0-23588000-1455875039_thumb.jpg

post-70634-0-13970900-1455875240_thumb.jpg

post-70634-0-72136200-1455875637_thumb.jpg

kingtube69 Experienced

kingtube69

Posted
Posted

Can vouch for this clutch and flywheel - I have the extra HD on my R33 and it's great. Drives really nice too.

Whoever buys this will be very happy with it.

GLWS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kapr
      ECU sees many times the speed than speedo does (R34 swap)

      By Kapr · Posted

      Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • albyz34gt
      34 de+t conversion using s2 stagea automatic transmission, engine harness and ecu

      By albyz34gt · Posted

      Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Duncan
      R32 GTS (RB20DE) Injectors Replacement

      By Duncan · Posted

      Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...