Jump to content
SAU Community

Recommended Posts

R33 intermittent loss of power.

Hi guys. 

I have an R33 gtst series 1.5 

List of mods

Full high Flow xforce exhaust 

K&N pod filter whith heat shield 

Blitz front mount intercooler 

Spit fire coils

New spark plugs ( unsure of brand) 

Power fc tuned by legend matt spry

Z32 airflow meter

Stock turbo running 13 pounds 

Car is making over 200kW at wheels

I have several issues. There are days when my car feels nice and responsive and goes like a bat out of hell. And there are days when I feel like I've lost about 30 hp through my mid range top end power. At times my accelerator feels less responsive / sluggish and boost doesn't feel like it comes on hard.

At times it feels like boost is flowing through a McDonald's straw. 

Now the other strange issue is sometimes when I stab the throttle to rev match the car will bog down but not always.  It's very inconsistent. And my fuel economy is terrible. 

I have also noticed some oil leaking from intake manifold. I was advised it could be a sqaushed gasket causing boost leak?

Only strange thing matt spry saw on the dyno was the 02 sensor was crapping out when the car is cold and dumping crap load of fuel but fixes itself when it warms up. 

Could it be piston or valve issue guys?

Problem is extremely frustrating and has been happening since I've owned the car. I just want my pride and joy to be running 100%

Any help would be appreciated guys.

 

DSC_0352.JPG

 

DSC_0352.JPG

DSC_0352.JPG

Edited by Redknight
Link to comment
https://www.sau.com.au/forums/topic/466641-r33-intermittent-loss-of-power/
Share on other sites

Where is this oil leaking from? Check your intercooler and pipes, could be full of oil which could be blown turbo seals.
It could also be broken ring lands, resulting in epic blowby which will dump heaps of oil in your intake. This is never good... This will put some oil on your AFM too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...