Jump to content
SAU Community

Recommended Posts

How can it because i want to get a r32 without a turbo because of the insurance and all, but what mods can i get to improve the horsepower, acceleration ect without a turbo.

This is gonna be my first car cos i am 17 now and 18 next year, but i just want some tips on how to improve the peformance of a r32 gts-t skyline without a turbo.

just changing the exhaust system to a larger unit.. opening up the air inlet with a pod or better panel filter should give you a good start.. then you can consider ecu remap or S-AFC.. then extractors. after that mb different cams, and porting the head a little (if you want to go that far into it). Could change the diff if its a manual to auto diff to give u a bit more acceleration off the line.

you have to remember though that the more mods (even if n/a) the more insurance will slug you, especially if you are a p-plater. maybe just keeping it stock for a while might be easiest (even if its just for a year)

Save your money - dont throw your cash away on trying to extract power out of the RB20DE or RB25DE.

Add some simple breathing mods, exhaust, headers & pod filter etc, but leave it at that

With the money you would spend on making the gts faster you could have bought a gtst.

I have thought about getting rid of the rb30e and dropping an rb25de into an r31 but it really isnt worth it. I think the most it would it making at the wheels with some mods would be 110rwkw. I doubt it would have the same torque output even with the same mods.

The rb20de would be even worse, torque is going to be pretty sad. When you have an N/A engine displacement makes quite a difference and is an advantage.

The rb30 with the same mods would have a similar output (90 - 100rwkw) but it would have more torque.

How can it because i want to get a r32 without a turbo because of the insurance and all, but what mods can i get to improve the horsepower, acceleration ect without a turbo.

Its been posted up on the forums a few times that the difference between N/A and turbo skylines isnt that much.

what mods can i get to improve the horsepower, acceleration ect without a turbo.

If you are serious about modding the rb20de go with what blitz said. Its simply not worth going any further apart from turbo charging it.

I think you'd get from 0-100km/h in around 8.2 - 9.0 secs.

I say, save you money up for a gtst. You will be thankful you did and the turbo makes a world of difference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...