Jump to content
SAU Community

RB20 Cutting out issue

Kubacca

By Kubacca,
in R Series (R30, R31, R32, R33, R34)

 Share

Recommended Posts

Kubacca Newbie

Kubacca

Posted
Posted

Hello, i have an RB20 Swapped s13 that has recently begun to cut out i have absolutely no idea why. It seems to drive fine nothing wrong then all of a sudden it cuts out its like the key has been turned off while im trying to accelerate it doesnt even have to be when im coming onto boost it can happen just randomly but normally between 2000-3500rpm. if im at a complete stop and it begins to do it, it sounds cammed and wil rev high then drop down to the point of almost stalling then rev back up then do the same thing. When its doing this i cant give it any accelerator at all it just bogs down, ive replaced the CAS twice, checked TPS, checked coilpacks, compression was fine. I have no idea what this could be, if anyone has any advice that'd be great :( things to note as well it has an IACV delete and stock ecu.

MODS

greddy td05

walboro 460

Splitfires

even with these mods it drove fine for months then all of a sudden has just started doing this.

Link to comment
https://www.sau.com.au/forums/topic/479368-rb20-cutting-out-issue/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Kelford 246-A2. 262in/272ex. 
    • Adam_ECR33
      Hello sau 👋

      By Adam_ECR33 · Posted

      Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • r32-25t
      Why am I hitting a power wall with my stroked RB25?

      By r32-25t · Posted

      When you say your cams are 272/262 is that 272in and 262ex?
    • Kinkstaah
      Nismo GT Pro LSD configurations

      By Kinkstaah · Posted

      We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...