Jump to content
SAU Community

Recommended Posts

gentlemen (and others)...

at 157k km on my rB25DE auto sedan and am getting an every-so-often A/T light, with the usual loss of whatever gear i'm in at the time. it always goes away once i restart, but i read the threads and watched every video and am told it will only get worse.

i have zero evidence anyone has ever done a trans flush on this car.

is there a chance that doing a flush will fix the problem, rather than the usual "replace the A/B solenoids"? just curious. rather not flush, seal it up again, then have to drop the pan all over again...

EWlQNeY.jpeg

 

5 minutes ago, GTSBoy said:

Get a scan tool on the Consult port and see what the TCU has to say for itself.

was my first thought, but a couple hundred for the cable/adapter plus not having a laptop that can run NIstune/NDSI/ECUtalk or any of the usual programs is the issue.

honestly i'm going to flush it anyways and so i guess this is a little like asking people to internet-diagnose my car. 

just wanted to see if anyone's ever had an A/T light go away purely by doing this though

On 10/28/2024 at 6:37 PM, GTSBoy said:

Just go to a quality workshop that has a quality scan tool and ask to plug it in for a few minutes. Throw them a six pack.

Nobody around me has a Consult (USA east coast) :( 

Either way I ordered all the parts to do a trans flush so guess I'll do it anyways.

4 hours ago, thatjawncrazy said:

Nobody around me has a Consult (USA east coast)

It's just not true. It does not have to be a "Consult". Professional grade scan tools from EVERY major workshop equipment electronics manufacturer will happily interrogate Nissan electronics. Things like Snap-On scan tools, etc. That is what they are for. This is why I said...

On 10/29/2024 at 9:07 AM, GTSBoy said:

Just go to a quality workshop that has a quality scan tool

 

On 11/1/2024 at 5:38 PM, GTSBoy said:

It's just not true. It does not have to be a "Consult". Professional grade scan tools from EVERY major workshop equipment electronics manufacturer will happily interrogate Nissan electronics. Things like Snap-On scan tools, etc. That is what they are for. This is why I said...

 

if I find a shop that has an OBD I tool and can connect it to the port - i wonder what the suggested route is for purposely triggering transmission limp mode while i happen to be within driving distance of the shop, and then dropping everything to stop by and have them scan it. so, it would be nice if things worked out that way - but in case they don't, we are back to my original question of "will bad fluid ever trigger limp mode on its own".

  • 1 month later...

interestingly enough, i found out the answer is yes. doing a flush did fix my recurring A/T light. it might have been because of the trans filter:

QyJqGs3.jpeg

but that doesn't really make sense to me. the fluid/filter was super dirty. would that increase the pressure in the lines and trigger an A/T light? does the car even have a way of detecting that? i have no idea. i've done 200+ miles after the flush and no A/T light. if my A/B solenoids went bad, i would think the light would've come on.

shifts and drives way better now though...at 2k rpm instead of 2500...no hesitation and downshifts when i want it to. 

wBfUdgK.jpeg

  • Like 1

Well, if that filter was impeding fluid flow, then it could have similar effects to faulty solenoids. The TCU will register a fault when it does something (ie, changes the state of a solenoid) and does not detect the required result. If there are other causes that can make the same lack of result, then they will be indistinguishable to the expected cause for which the TCU has a code.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To be determined, Luke, to be determined. 😁 Definitely the car
    • It might be worth having a good look at the chassis behind the bumper then; most people prefer the series 2 look so it might have been changed to cheaper parts as part of an earlier repair
    • The car itself a series 2. I was just curious about the headlights and just wanted to confirm that they were series 1. Good to know the rest of the front end is series 1. It’ll be easier for me to find parts on the aftermarket side of things lol
    • If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
×
×
  • Create New...