Jump to content
SAU Community

What should this run?

7heavn

By 7heavn,
in Motorsport Discussion & Builds

 Share

Recommended Posts

7heavn Experienced

7heavn

Posted
Posted

Hey Guys

Going to take the GTR down to WSID in a few weeks for a run down the 1/4 mile , I've been doing abit of reading on these forums to try and work out what times the car should be roughly good for , I've seen some very differen't results though.

Basically the run down on the car is it's an r32 GTR with really no extra weight ( stero's and the like) , I have a dyno graph from the previous owner from when the PFC was installed and tuned at C&V which is for 275kw@all four wheels. In this form on a perfect run what should the car be able to do ? , I'm hoping for high 11's am I asking too much?. What would 275kw@at all four be in rwkw as I am a little confused on how it would be worked out seeing as it is not a constant 4wd (coming from a wrx back ground here) .

Also another thing with the car it has adjustable cam gears but they haven't been fiddled with yet and are at the stock setting's. If I'm chasing a decent 1/4 mile time should I be looking to get them adjusted for peak power , mid range , or low down . I know that last one might be a stupid question as I have my own thoery on what I should be looking at getting them adjusted for just wanted to check with the people who are in the know .

cheers

Brett

Link to comment
https://www.sau.com.au/forums/topic/49066-what-should-this-run/
Share on other sites
MrBlonde Community Regular

MrBlonde

Posted
Posted
Hey Guys

Going to take the GTR down to WSID in a few weeks for a run down the 1/4 mile , I've been doing abit of reading on these forums to try and work out what times the car should be roughly good for , I've seen some very differen't results though.

Brett, there's one good way to find out ...

MrBlonde Community Regular

MrBlonde

Posted
Posted
Nice M coupe by the way I've admired it at the last few street meeting's at WSID nice to see the times are dropping and starting to live up to that awsome trap speed

Thanks Brett. It's not as easy as it looks!

Provided ANDRA scrutineers pass the car with the front runners and slicks we should see a better ET with some decent traction. Here's hoping!

  • 3 weeks later...
  • 3 weeks later...
7heavn Experienced

7heavn

Posted
  • Author
Posted

Finally got out there last night only got to have one run due to the rain coming down . First and only run was 12.3@111mph with the whole front splash tray bent down and dragging the track from about halfway. Little dissapointed with the trap speed but putting it down to the gravel tray for now . Car made 275rwkw at unigroup the week before I would say this power should be good enough to trap 115-117mph ??? what do you guys think.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • joshuaho96
      Automatic Power Button Light Flashing

      By joshuaho96 · Posted

      Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...