Jump to content
SAU Community

Fludder..

|PRESA|

By |PRESA|,
in Engines & Forced Induction

 Share

Recommended Posts

|PRESA| Proficient

|PRESA|

Posted
  • Author
Posted
If I am reading this right, you know its not to good for the turbo to block off the BOV??

You may already know this, but just thought I would check...

The amount of stress it actually puts on your turbo is well over rated.

Why do VL's run fine with out the bov? Answer me that

Link to comment
https://www.sau.com.au/forums/topic/51220-fludder/#findComment-1014976
Share on other sites
R324D Community Regular

R324D

Posted
Posted
they would run well for a while, but that doesnt mean it there is no long term effect.

VL engines are old technology. if bovs werent needed then they wouldnt have put them on new cars.

Exatly what I was thinking...

You can't say that it is all fine because VL's don't have them, cause if it was all fine they wouldn't of introduced them to new cars...

It won't make your turbo shit itself overnight, but it does increase the shaft play of the turbo... Think about it, the turbo is spinning one way, you clutch, air has nowhere to go but back through the turbo the oppisite way to its spinning...... that can't be good.

Anyways not here to argue about it, I am sure everyone has their own opinion on it, and I am no expert. Just letting you know if you hadn't thought of it, which obviously you had.... so I withdraw my 2 cents worth :rofl:

Link to comment
https://www.sau.com.au/forums/topic/51220-fludder/#findComment-1015500
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • Ozdavroz
      Starting again

      By Ozdavroz · Posted

      I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • sonicii
      Steering lock/control unit Infiniti G37

      By sonicii · Posted

      Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
    • Dose Pipe Sutututu
      What brakes on R34 GTT(Europe)

      By Dose Pipe Sutututu · Posted

      Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • soviet_merlin
      WGNC34 - floor mats

      By soviet_merlin · Posted

      Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
×
×
  • Create New...