Jump to content
SAU Community

Recommended Posts

Hey guys just interested to find out how guys launch their beast at the drags.

Do you guys like to do a burnout to warm up yout tires or just get on with it?

And a question for the guys who have been down to the track for a run what are the impressions of other drivers of your beast?

:whackit:

:cheers:

Link to comment
https://www.sau.com.au/forums/topic/53722-launch-techniques/
Share on other sites

7700rpm against a launch limiter, release clutch

Thanks but not much help, the std rev limiter seems to be at 7,500 rpm and mine's an auto.

In the dry I stand on the brakes, hard. Stick it in drive and raise the revs until the torque converter holds the rpm there. Take foot of brake and floor the accelerator. No wheelspin from the standard engine just :wavey:

In the wet I ..... well exactly the same :wavey:

So I need more power then we might get some :burnout:

:cheers:

bring on the burning rubber.

when i see gtrs down at the drags or on dvd's when they warm up their tyres they always do a huge burnout, but they only smoke the rear tyres how does that work? are they in 2wd mode or something? or does using the brake to ensure you dont roll stop the front from spinning?

bring on the burning rubber.

when i see gtrs down at the drags or on dvd's when they warm up their tyres they always do a huge burnout, but they only smoke the rear tyres how does that work? are they in 2wd mode or something? or does using the brake to ensure you dont roll stop the front from spinning?

They stick them in 2wd to warm up the rear tyres as they cop most of the launch load. They have a line locker on the front brakes to hold them while the rears spin. :cheers:

I used to just hold the brake down while i floor the accel. after 4-5 secs wheels would start spinnin slow then after 30 secs a good amount of smoke was comin out from under, would keep going and gettin faster if i kept it there, but this was on 11psi and shell optimax with redex octane boost.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
    • Yes, unfortunately that's the one. Signal was noisy to begin with; after driving once and looking back at the logs I saw pressure constantly swinging between 0-200psi, or staying at 0 randomly for a few seconds. There's a lot of good sensors that share the same look and feel, so don't presume they're all bad. I bought mine for 20$ off Amazon and I should have read the reviews prior, as it's clear they're junk.  I purchased a lowdollerr motorsports sensor. 
    • wedding eh.....I seem to get to more funerals than weddings or christenings these days....
×
×
  • Create New...