Jump to content
SAU Community

Recommended Posts

Hey guys just interested to find out how guys launch their beast at the drags.

Do you guys like to do a burnout to warm up yout tires or just get on with it?

And a question for the guys who have been down to the track for a run what are the impressions of other drivers of your beast?

:whackit:

:cheers:

Link to comment
https://www.sau.com.au/forums/topic/53722-launch-techniques/
Share on other sites

7700rpm against a launch limiter, release clutch

Thanks but not much help, the std rev limiter seems to be at 7,500 rpm and mine's an auto.

In the dry I stand on the brakes, hard. Stick it in drive and raise the revs until the torque converter holds the rpm there. Take foot of brake and floor the accelerator. No wheelspin from the standard engine just :wavey:

In the wet I ..... well exactly the same :wavey:

So I need more power then we might get some :burnout:

:cheers:

bring on the burning rubber.

when i see gtrs down at the drags or on dvd's when they warm up their tyres they always do a huge burnout, but they only smoke the rear tyres how does that work? are they in 2wd mode or something? or does using the brake to ensure you dont roll stop the front from spinning?

bring on the burning rubber.

when i see gtrs down at the drags or on dvd's when they warm up their tyres they always do a huge burnout, but they only smoke the rear tyres how does that work? are they in 2wd mode or something? or does using the brake to ensure you dont roll stop the front from spinning?

They stick them in 2wd to warm up the rear tyres as they cop most of the launch load. They have a line locker on the front brakes to hold them while the rears spin. :cheers:

I used to just hold the brake down while i floor the accel. after 4-5 secs wheels would start spinnin slow then after 30 secs a good amount of smoke was comin out from under, would keep going and gettin faster if i kept it there, but this was on 11psi and shell optimax with redex octane boost.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...