Jump to content
SAU Community

Recommended Posts

I have never seen it, BUT the S15 fronts are not a simple bolt on addition to the S13's so therefore, don't expect them to go on without modification onto cefiro or laurel.

However with the kits available for S13's i would not imagine it would be too difficult. Would look a bit screwed up in my opinion though.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089402
Share on other sites

haha well its got some skyline bits, and its got some s13 bits... and maybe more :) *oooh the suspense*

i wouldn't say bolted... lol you should check out some of the conversion jobs, shit like held on by an aluminium bracket that you can bend by hand n stuff. Then there's the bog jobs... thems real fun.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089427
Share on other sites

However with the kits available for S13's i would not imagine it would be too difficult. Would look a bit screwed up in my opinion though.

Actually the kits for the S13 and RPS13 isnt that difficult.

Ive seen the kit for it and its easy to put together... i was going to get one for my mates RPS13 for 1800 including the lights, flared guards and vertex bar.

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089546
Share on other sites

isn't she purrrdy? we found her in the scrap parts section of yahoo auctions, checked the VIN, it was a 1989, only problem was that the engine was siezed, so we organised it to be trucked to the port and loaded. couldn't make up some ramps coz it was too low n stuff so had to send the mechanic out to mess with it.

Interior is clean as, with custom gauge install (not usual caveman style drill holes everywhere and poke shit in) in the centre console etc.

cost next to nothing cos it was a part taking car :)

Link to comment
https://www.sau.com.au/forums/topic/56130-ichigo-cefiro/#findComment-1089950
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...