Jump to content
SAU Community

Recommended Posts

Hey Guys,

First time poster, but i've been lingering reading for some time. I am currently looking at MY97 RS Four Stageas, and have a few questions.

1) Anyone know any good places for the RB25 and Stagea's around brisbane (workshops, mechanics etc), i would like to get a car checked out before i buy it, are there any telltale signs for these things?

2) i'm a bit worried about kms, everything i've looked at is around the 40k kms mark, which seems a bit low for a 97 model car, is there anything that i can check to make sure kms are legit?

3) how expensive are nissan 4wd systems when they go bad? coming from owning a mid 60's mercedes coupe so parts pricing doesn't scare me, but do they go wrong often?

4) how available are parts? do i need to get someone in japan onside to send me stuff, or is most stuff available through nissan? and where do i find workshop manuals in english?

5) anything i shoud be particuarly careful of buying? preferable models? from what i can tell theres a few engine options, but most i've seen are RB25 RS Four's how do i tell the difference between a Neo and non Neo?.

Thanks in advance for the answers, i hope i don't appear like too much of a noob! hopefully soon i'll have a stagea to post pics of!.

Russ

G'day Russ,

I'll see how I go at your questions.

2. KM's can be a bit sus sometimes. But there are cars out there that have done very low KM's. Check the usual interior items for signs of high wear.. Carpets, mats; seats, steering wheel etc.. They will give you a good indication.

3. I've never actually heard of a ATTESSA system stuff up. I have heard of the very rear case that someone burns out the clutch pack in the centre diff, but it's usually cause they were doing something wrong eg. not disabbling the 4wd correctly, or running different sized wheels/tyres front to back.

4. Parts are available through most Nissan dealers. Prices are pretty reasonable considering. Theres also a heap of parts importers nowadays too.

5. Do a heap of looking around and try and get the best for your money.

I'm actually considering selling mine to downgrade to something cheap so I can use the mony to study part time. Time for a career change...

J

As for NEO & non-NEO, the NEO engined cars were the series 2, which you can tell from the front because they have the headlights with 2 seperate lenses, rather than all in one rectangular block.

Someone with more knowledge than me might be able to tell you in more detail, but that's an obvious difference.

Try http://www.geocities.com/mcnamg/ for more details of models, features, etc.

Mine came with service manuals so I could check the K's and the dates. I also checked the cam belt change date and K's and calculated if the K's were realistic from that. The steering wheel and drivers seat wear rates were also consistent. Most of all I used someone I could trust to source it in Japan.:P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • BRUH, one of the biggest mistakes of my life..... and i've had plenty ;[)
×
×
  • Create New...