Jump to content
SAU Community

Recommended Posts

Its the leak yes, It happed to me before...

What it is that, where steering arm located it has Plasric/rubber cover is torn at the top.

It possibley make some kind of winding noise if you try to turn the steering wheel.

check your fluid tank and the rubber.plastic sleeve cover on steering arm.

even resiviour is full if there is leak on the top of the steering arm sleeve.

if your power steering resiviour bubble when car is stationary or not(turning). means there is leak some where.... ( my guess would be those one of steering arm rubber/plastic covers.

Run your fingers over them (squizze them) to check for leaks.

also if mechanic is the only option can someone make a recomendation?

Hey, i have the same problem, just yesterday the HICAS sign decieded to pop up, in the past all i had to do was top up the fluid! but not time time :) mine doesnt make any sound thou !! fluid is fine doesnt bubble so im hopeing its just a leak?? should put it up on the ramps go have a look!

I noticed this grinding noise the other day whilst parking my R32 gts.. under the fluid resivouir i notice there's alot of dirty fluid where it looks as its been leaking (i've been topping it up).. i'm putting the car on the hoist tommorow to check the suspension anyway, so while i'm there i'm going to drain the ps fluid and check all the hoses

even resiviour is full if there is leak on the top of the steering arm sleeve.

 

if your power steering resiviour bubble when car is stationary or not(turning). means there is leak some where.... ( my guess would be those one of steering arm rubber/plastic covers.

 

Run your fingers over them (squizze them) to check for leaks.

The sleeve which is called a rack boot does not seal the fluid.

The rack seal stops fluid coming out of the housing. If there is any fluid inside that boot then the seal is broken. The boot only stops dirt from getting inside to where the seal is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...