Jump to content
SAU Community

ER34 restrictor - from boost hose

NismoR34

By NismoR34,
in Wanted to Buy

 Share

Recommended Posts

NismoR34 Grand Master

NismoR34

Posted
Posted

Hi all.

I am after a very small metal part - one of the restrictors from the hose that runs from the top of the turbo to the factory boost solenoid. I will try and take a pic [macro] on the weekend in case you don't know what I am talking about!

There are 2 of these restrictors on a stock boost arrangement [er34].

If you have a bleed valve or EBC chances are you have a spare restrictor :)

Not sure if r34 GTR or 33 [any] are the same but if they are then that will do too!

Cheers

Dale

Link to comment
https://www.sau.com.au/forums/topic/58271-er34-restrictor-from-boost-hose/
Share on other sites
  • 2 weeks later...
NismoR34 Grand Master

NismoR34

Posted
  • Author
Posted

I am missing one [out of 2] and to run stock boost I need a 2nd one.

As far as I know GTR's only have one but the RWD turbo skylines have 2!

Let me know if you no longer need it and I will buy it off ya :thumbsup:

Cheers

Dale

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      NC MX5

      By Duncan · Posted

      sorted
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Thanks mate.
    • TurboTapin
      Crank Motorsports Front Axles

      By TurboTapin · Posted

      I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...