Jump to content
SAU Community

Recommended Posts

70 according to the wiseco information sheet, all the ones ive ever done have been at least 66, theres an obvious difference between 25s and 26s the 26 chambers are alot deeper, all these 63cc rb26s must have been milled heaps to get them that low, if you do a comp ratio calculation using 63cc chambers youll end up with higher than the factory 8.5 to 1.

how can 25 heads with comp ratios of 9 to 1, smaller crown on the piston and a shorter stroke have the same cc chamber as 26 heads that have 8.5 to 1 comp ratio, if the stroke of the 26 is longer and the crown on the piston is bigger then with the same chamber volume the 26 comp ratio will be higer than 9 to 1.

ace_nz, this was the thinking behind my question. I have a stock Nissan RB26DETT piston, and a stock Nissan RB25DET piston here on my desk, the crown protrusions differ as you say.... Hmmm. I am asking this as i have been offered an HKS 2.8 stroker kit, brand new, at a good discount, and am trying to work out the compression if I fit this kit into my RB25DETT block with RB25DET head.

Arias Pistons for RB30s with twin cams head have 2 part numbers ,one for 25 head and one for 26 head.I have to CC pauls head and a stock GTR head this week as he has an RB26 crank going in to his RB25 and i need to work out the pistons i need to use.Will post the details then.

one thing you guy might have over looked here it the piston to deck hieght of block the head and piston from 25 and 26 could be just as you said but if the piston to deck height could be quiet different (i dont know this just idea that could expain the problem)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...