Jump to content
SAU Community

Recommended Posts

Hey guys hope someone can help me. I have just recently been given a Nismo Short shift for my skyline from a friend who owns a recking yard, well he said it was a Nismo one anyway but it is missing the little plastic bit on the end.

Have tried using the standard one no good gets stuck also tried using a VL Turbo one no good.

Would anybody know were I could buy one from or even has one laying around that would fit sweet.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/61186-need-help-with-nismo-short-shift/
Share on other sites

have you actually tried putting the stocker in a vice and prying it off?? thats how i got mine of, it snapped cause i wasnt careful but i just locklite it together again. and yes you cant pull it off by hand other wise it would fall off into the gbox when u took it out in the first place.

hope that helps.

Yeah I have tried putting the stocker in but it jams and doesn’t shift at all. I even tried it with nothing worked fine, it just had a little play when it N. Look might not even be for R33.

Yeah it has a spacer spacer on it. Can't remember if he got it off a 33 or a 34????

Any major differences?? I might post a picture in a few days so you guys get a better picture of what I have.

Thanks for the input. :rofl:

i know with the r33 the ball / socket part on the end of the shifter is the same size with both series 1 + 2 but the actual plastic bit is that clips on the end is a different size. Not too sure about 34 though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...