Jump to content
SAU Community

Recommended Posts

I just fitted some new Hawk Racing pads to my calipers and they squeal loudly when I slow and approach stop - they are ok at speed. I have not been braking hard as I am bedding them in slowly. I have taken them out and put the orange anti squeal paste between the shims and the pads, I have had them in for a week and I have done 260k's on them so far. I have followed the bedding in procedure as laid out on Hawks own website, yet my lovely new brakes continue to make teeth grating +100db squeals when I slow down.

What I want to know is - will this eventually go away, are there any issues specific to stock rotors and Hawk pads that may cause this, is there anything I should/can do.

My discs have been checked out and are fine with no wear, lines, blue, or marks. I am in MC motosport next Sunday and I want to get it sorted by then or I might have to put the original pads back in so as not to kill the hi frequency part of everyones hearing. Besides the squeal they are bloody nice pads.

Thanks :D

Link to comment
https://www.sau.com.au/forums/topic/63664-screaming-brakes/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...