Jump to content
SAU Community

HIT & RUN

j4h012

By j4h012,
in New South Wales

 Share

Recommended Posts

Goon Experienced

Goon

Posted
Posted

last week, a truck driver hit my dads bmw rear panel and spun the car out and caused alot of damage and both my parents were shaking. the f*cker (pardon my french) drove off. we got the plates, reported it to the police and they said there was no point in following it up as the driver would only deny it (apparently its a regular occurance)... my dad made them follow it up, but they rang him 1 hours later said they "rang him", that the driver denied it...

(breathes) serenity now... serenity now..., though i cant say the same for my dad, the car is his baby.

sorry to hear about ur incident man, i know how it is!

Link to comment
https://www.sau.com.au/forums/topic/64279-hit-run/#findComment-1205789
Share on other sites
Mr R32 M-Spec Experienced

Mr R32 M-Spec

Posted
Posted

truck drivers are f#$cked man

My mates RX got side swiped coming onto the freeway, truck came in at the entry ramp, over 2 lanes and almost sent him in to the middle barrier, and just sped off. 2K or so worth of damage. somebodys gonna give chase one day till they stop....

mark

Link to comment
https://www.sau.com.au/forums/topic/64279-hit-run/#findComment-1207546
Share on other sites
Goon Experienced

Goon

Posted
Posted

Ok... You guys are not going to believe this but the Beemer got swipped AGAIN by a truckie. The Beemer was parked in a side street in Bronte and a truck came screaming down the narrow street, snapped the wing mirror back, smashing the mirror and destroying the mirror housing-body itslef. But these guys had a much better brain than the other ones and stopped. They'll pay out for the damage, so we'll see what happens.

This is def not the "year of the B-M". my dad's had the car for over 3 years, it 'was' immacalate and not a single blemish, now its been defiled twice in the space of a single week! Maybe they go the gist we dobbed in their mate.

Beno, not sure man! these guys were sketchy characters... lebanese. i reckon I round up the SAU boys and DTMpower guys to gang up on these mo'fos!

Link to comment
https://www.sau.com.au/forums/topic/64279-hit-run/#findComment-1207703
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...