Jump to content
SAU Community

WANTED: 2 Standard R33 16/7.5 inch rims

PATR33

By PATR33,
in Wanted to Buy

 Share

Recommended Posts

PATR33 Contributor

PATR33

Posted
Posted

People could please make sure that if you do have these rims they are not the 6.5inch wide version. They are stamped 16/7.5 45 offset on one of the inside spokes.

These rims are possibly off the AWD non GTR Skylines not sure. But I have definately got two 7.5inch wide R33 Skyline Rims and I want 2 more.

Or will take 4

Link to comment
https://www.sau.com.au/forums/topic/66467-wanted-2-standard-r33-1675-inch-rims/
Share on other sites
PATR33 Contributor

PATR33

Posted
  • Author
Posted
my stockies are 6.5 wide all round.  i thought they were all like that.  might have to have a look again.  N/A's have 4 studs instead of 5 so they wouldnt be that.

Perhaps 7.5 inch wide are Series 2 rims.

PATR33 Contributor

PATR33

Posted
  • Author
Posted
i have two.

lemme know.

This should be in the Wanted To Buy section mate.

Yeah sorry about posting here, I thought this was the place for Victorian stuff.

Just sent an email to your hotmail.

Thanks

Pat

  • 4 weeks later...
  • 2 weeks later...
PATR33 Contributor

PATR33

Posted
  • Author
Posted
i have a full set of 300zx rims, willing to seperate for the right price. Let me know if you are interested. they are 16inch, 5 stud, not sure about the width and offset, but can check if you want.

Please check and get back to me.

If they are 16 7.5/45 offset they are right.

Chef_32 Mentor

Chef_32

Posted
Posted

ha. you're in luck.

I tried measuring with a tape, but that got me all confused cos i didn't know where to measure from. Then i loked for writing on the inside of the wheels and found......16X7(1/2) JJ 45

looks like i've got what you are after.

PATR33 Contributor

PATR33

Posted
  • Author
Posted
ha. you're in luck.

I tried measuring with a tape, but that got me all confused cos i didn't know where to measure from. Then i loked for writing on the inside of the wheels and found......16X7(1/2) JJ 45

looks like i've got what you are after.

Very good.

Just pm me a contact number and we can take it from there

Thanks

benm Grand Master

benm

Posted
Posted
They must be stamped 16/7.5 45 offset.
I think you are confusing R33/S15 wheels with the old 300ZX rims.

Also I just checked both (I have a set of both) and neither have any measurements stamped on them inside or out).

PATR33 Contributor

PATR33

Posted
  • Author
Posted

On my car the fronts are 16/6.5 and the rears are 16/7.5 and this is definetely stamped on the inside spokes.

I'm not sure what car the 7.5's came from but all I know is that they look identical to the front 6.5's..

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok so will run the piping over that radiator and no plenum it is. Put that money towards a Haltech and see what suits. Any ideas something like an elite 2000 or 2500 right? My long term goal is 300kw e85 and manual swap and that’s a dream come true. For now will be 200kw and auto the stock rb25det neo intake isn’t too expensive with throttle body. If I was to have the port matching done, Would that be better than the stock de intake as the det has bigger holes plus has the spots for sensors etc? And suit more long term?  appreciate the advice?   
    • MBS206
      R33 GTR running -9 with no tune

      By MBS206 · Posted

      You understand AFR is not the only thing that contributes to it pinging yeah? Funnily, what the AFR gauge will tell you when it likely is pinging, is going to make you think things are really safe and good.
    • MBS206
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By MBS206 · Posted

      Run the piping how we all have for decades. Also the duel runners with the +T setup dramatically helps it gets on boost quicker. Yes, chase huge power it'll become a problem, but you're a long way off when you're already saying an aftermarket ECU is out of the budget. You also say NisTune as it's simple, and then immediately say it'll be painful, meaning... It won't be simple. It will likely cost you a lot more stuffing around with a Nistune, than just putting a Haltech or similar in.
    • 677_GTR
      R33 GTR running -9 with no tune

      By 677_GTR · Posted

      I’ll order an afr gauge to keep an eye on it.  Then will get a haltech soon 
    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      TD05 or maybe pulsar PSR2867r Gen 2?  id love a garret but it’s quite out the budget for now and I’m not chasing crazy power.    yeh fuel pump haven’t looked into but whatever works, kind of last on my list.    Nistune because it’s simple but Ik it’s a lot of pain especially as I’m auto +t with the whole seperate TCM etc still investigating that. Haltech id love but once budget tight for now atleast.    finally the reason I’m trying for a plenum instead of the stock intake is I already have a standard Intercooler mounted etc. so the ports are on both sides so trying to not have to go over the clutch fan radiator etc. trying to find a good deal return flow if I don’t than this will do for now I guess. btw any ideas with that, apparently some people have to cut blades to reduce it from hitting the Intercooler piping over the radiator ? Thanks 
×
×
  • Create New...