Jump to content
SAU Community

FS: Rays Volk Challenge 18"

j-plus
 Share

Recommended Posts

j-plus Enthusiast

j-plus

Posted
Posted

Hi Guys,

Its been a while but j-plus is back again! We’ve been working hard to have more regular shipments and are now at a stage where we will be shipping once per month. Unfortunately, not a lot is available (once again!) because it all gets snapped up before it arrives in the country.

Remember that we DON”T:

 Post pics from the auctions of wheels we don’t have and probably can’t get

 Try and sell +45 offset wheels for your Nissan and tell you “she’ll be right”

 Feed you mouthfulls of bullsh!t

We only sell wheels we actually have and if we don’t have it, we’ll try and get it.

We are the most honest, most reliable and most fair sponsor you will have the pleasure of dealing with!

Rays Volk Challenge

F: 18 x 8 (+32) 235/40/18

R: 18 x 9 (+35) 265/35/18

Come with Bridgestone Potenza tyres with approximately 65% remaining

Perfect fit for R32/R33/Z32/R34/S14 – careful on the rears of S15

Condition best described as excellent

Real pics of the real wheels available tomorrow

$1,940

As always, sending interstate is no problem!

Also available, Volk Rays Challenge 18 x 10 (+20) all round to suit GTR, tyres are quite low - New thread up soon…

Kind Regards,

Jeff.

Link to comment
https://www.sau.com.au/forums/topic/67376-fs-rays-volk-challenge-18/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R34 Skyline climate control unit transistor

      By dbm7 · Posted

      Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • GTSBoy
      Another "where do these lines and plugs go" RB25DET question

      By GTSBoy · Posted

      4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • GTSBoy
      R34 GTR Seats / No longer reclining

      By GTSBoy · Posted

      Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • GTSBoy
      R34 Skyline climate control unit transistor

      By GTSBoy · Posted

      Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...