Jump to content
SAU Community

R33 GTST cold air partition

skyline33

By skyline33,
in Wanted to Buy

 Share

Recommended Posts

Jay95R33 Grand Master

Jay95R33

Posted
Posted

300 !!!! holly craparoonie.....

The one I've got is that 10mm heat proof foam that has a silver heat reflective layer on it.

But I'm not sure if it'll fit a Blitz SUS filter. I sort of custom made it for my HKS filter.

BTW: check out the new smilie :lol: what a dude.....

Guest DON91E

Guest DON91E

Posted
Posted

HAHAHAHAHHA

I was thinking of same thing!!

i was saying to myself " if these things can help keep heat out of my car then....[insert light bulb here]"

I also went to clark rubber and bought some heat reflective foam.

Foam on one side HEATER on the other, this stuff does not WORK!

anyone know wat im supposed to look for when i go into Clark rubber?

Donnie

Jay95R33 Grand Master

Jay95R33

Posted
Posted

What I found made a big difference was to make sure that the pod is sealed from sucking air from the engine bay. It wasn't so much as the radiant heat, but the hot air that kills performance.

So I think the foam stuff would be fine if you make sure that it's sealed correctly.

It's no use just putting a heat shield there with big gaps around it and hope that it works. I'm sure it would stop alot of radiant heat, but it'll still suck in heaps of hot air. And hot air is the killer :)

Anyway, just my 2c

;)

J

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...