Jump to content
SAU Community

Recommended Posts

Brand new garrett GT Series BB turbo rated at 500hp. This is also

known as the GT30R 56T model

Front A/R is 0.6 (clears headers and Engine mount!)

Rear A/R is 0.82

4'' inlet with massive bell mouth to suck in plenty of laminar air

with surge shroud (similar to HKS 3037S)

2" outlet to suit intercooler pipe work

Turbine housing: GT30 non wastegated.

Inlet: T3

Outlet :GT30

Ball bearings allow the turbo spin forever, even when spun by hand and increadible reliability on high boost. I have seen these making 300 Rw kw on 17 PSI!

Item includes Garrett warranty from date of purchase.

Unlike bushed (STD wet floating bearing) turbos that need replacing/rebuilding

at 40,000 klm in performance applications, this will only require new oil seals

at 80,000 klm. This means long term savings!

Utilizing the latest compressor and turbine wheel design these have proved to

spool up even faster providing more drivability, stronger midrange power and torque with better reliability.

Inconel turbine shaft which is extremely light allowing quicker turbo response

and heat resilient this turbo is top shelf with no expense spared.

Recommended retail is $2960

Turbo only $1799

____________________________________________________________

HKS Cast manifold.

This will not crack! In addition it can be further ported, extrude honed etc for further improvement if need be. As you can see from the pic's, the design is pretty good. All runners are split as far up to the collector as possible which will give good top end and mid range performance. It even splits the wastegate gasses.

This has a T3 flange, but is big enough to be drilled for a T4 flange if required.

I usually use these with GT30/35/40 BB turbo's due to the T3 flange. Due to the low mount design, you minimize any unwanted attention from the cops! If you need more info feel free to Pm me.

ON HOLD

c2_1_b.JPG

50_1.JPG

e5_1.JPG

b8_1.JPG

d1_1.JPG

1b_1.JPG

____________________________________________________________

Brand new HKS Style wastegate to suit.

45mm Valve, silicon/nomex doaphram and 12 psi spring

$250

There is no warranty on this wastegate as I got it cheap and am selling it for what cost. It is NOT an original HKS wastegate (otherwise it would be $1300)

____________________________________________________________

Manifold and Turbo combination $POA

RB25DET Nismo 550 cc injectors $750 cleaned and shipped

RB20DET/RB26 HKS 550cc injectors $750 cleaned and shipped

ff_1_b.JPG

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...