Jump to content
SAU Community

GT30R and RB20/25 HKS manifold (new!) & 550cc Injectors! 3rd gear tyre fryin' anyone?

amosite
 Share

Recommended Posts

amosite Proficient

amosite

Posted
Posted

Brand new garrett GT Series BB turbo rated at 500hp. This is also

known as the GT30R 56T model

Front A/R is 0.6 (clears headers and Engine mount!)

Rear A/R is 0.82

4'' inlet with massive bell mouth to suck in plenty of laminar air

with surge shroud (similar to HKS 3037S)

2" outlet to suit intercooler pipe work

Turbine housing: GT30 non wastegated.

Inlet: T3

Outlet :GT30

Ball bearings allow the turbo spin forever, even when spun by hand and increadible reliability on high boost. I have seen these making 300 Rw kw on 17 PSI!

Item includes Garrett warranty from date of purchase.

Unlike bushed (STD wet floating bearing) turbos that need replacing/rebuilding

at 40,000 klm in performance applications, this will only require new oil seals

at 80,000 klm. This means long term savings!

Utilizing the latest compressor and turbine wheel design these have proved to

spool up even faster providing more drivability, stronger midrange power and torque with better reliability.

Inconel turbine shaft which is extremely light allowing quicker turbo response

and heat resilient this turbo is top shelf with no expense spared.

Recommended retail is $2960

Turbo only $1799

____________________________________________________________

HKS Cast manifold.

This will not crack! In addition it can be further ported, extrude honed etc for further improvement if need be. As you can see from the pic's, the design is pretty good. All runners are split as far up to the collector as possible which will give good top end and mid range performance. It even splits the wastegate gasses.

This has a T3 flange, but is big enough to be drilled for a T4 flange if required.

I usually use these with GT30/35/40 BB turbo's due to the T3 flange. Due to the low mount design, you minimize any unwanted attention from the cops! If you need more info feel free to Pm me.

ON HOLD

c2_1_b.JPG

50_1.JPG

e5_1.JPG

b8_1.JPG

d1_1.JPG

1b_1.JPG

____________________________________________________________

Brand new HKS Style wastegate to suit.

45mm Valve, silicon/nomex doaphram and 12 psi spring

$250

There is no warranty on this wastegate as I got it cheap and am selling it for what cost. It is NOT an original HKS wastegate (otherwise it would be $1300)

____________________________________________________________

Manifold and Turbo combination $POA

RB25DET Nismo 550 cc injectors $750 cleaned and shipped

RB20DET/RB26 HKS 550cc injectors $750 cleaned and shipped

ff_1_b.JPG

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...