Jump to content
SAU Community

Recommended Posts

Brand new garrett GT Series BB turbo rated at 500hp. This is also

known as the GT30R 56T model

Front A/R is 0.6 (clears headers and Engine mount!)

Rear A/R is 0.82

4'' inlet with massive bell mouth to suck in plenty of laminar air

with surge shroud (similar to HKS 3037S)

2" outlet to suit intercooler pipe work

Turbine housing: GT30 non wastegated.

Inlet: T3

Outlet :GT30

Ball bearings allow the turbo spin forever, even when spun by hand and increadible reliability on high boost. I have seen these making 300 Rw kw on 17 PSI!

Item includes Garrett warranty from date of purchase.

Unlike bushed (STD wet floating bearing) turbos that need replacing/rebuilding

at 40,000 klm in performance applications, this will only require new oil seals

at 80,000 klm. This means long term savings!

Utilizing the latest compressor and turbine wheel design these have proved to

spool up even faster providing more drivability, stronger midrange power and torque with better reliability.

Inconel turbine shaft which is extremely light allowing quicker turbo response

and heat resilient this turbo is top shelf with no expense spared.

Recommended retail is $2960

Turbo only $1799

____________________________________________________________

HKS Cast manifold.

This will not crack! In addition it can be further ported, extrude honed etc for further improvement if need be. As you can see from the pic's, the design is pretty good. All runners are split as far up to the collector as possible which will give good top end and mid range performance. It even splits the wastegate gasses.

This has a T3 flange, but is big enough to be drilled for a T4 flange if required.

I usually use these with GT30/35/40 BB turbo's due to the T3 flange. Due to the low mount design, you minimize any unwanted attention from the cops! If you need more info feel free to Pm me.

ON HOLD

c2_1_b.JPG

50_1.JPG

e5_1.JPG

b8_1.JPG

d1_1.JPG

1b_1.JPG

____________________________________________________________

Brand new HKS Style wastegate to suit.

45mm Valve, silicon/nomex doaphram and 12 psi spring

$250

There is no warranty on this wastegate as I got it cheap and am selling it for what cost. It is NOT an original HKS wastegate (otherwise it would be $1300)

____________________________________________________________

Manifold and Turbo combination $POA

RB25DET Nismo 550 cc injectors $750 cleaned and shipped

RB20DET/RB26 HKS 550cc injectors $750 cleaned and shipped

ff_1_b.JPG

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • This. The R34 handbrake icon DOES come up when the brake fluid level is low. You might be sitting right on that threshhold. I have been down this diagnosis path and this was the solution (and it was pretty much as full as your picture is to begin with).
    • Unfortunately the cavaet to that is that while any scan tool should be able to read the code, the workshop will need a consult plug to OBD socket adapter. You don't have a location on your profile, where are you based?
    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
×
×
  • Create New...